Abstract:Purpose The purpose of this paper is to optimise the electro‐discharge machining (EDM) parameters and investigate feasibility of using direct metal laser sintering (DMLS) parts as EDM electrodes. Design/methodology/approach In this paper the effects of discharge current, pulse‐on‐time, flushing pressure are optimized for minimum tool wear rate (TWR), maximum metal removal rate (MRR) and minimum surface roughness (Ra). Taguchi‐based L 9 orthogonal array has been used for performing experiments on EDM machining of EN 24 steel using DMLS electrodes. The grey relational analysis combined with ANOVA techniques have been employed to determine the optimal level as well as their significance. Findings Experimental results have shown that the performance characteristics of the EDM process (TWR, MRR and surface roughness) using DMLS electrode can be quantified and controlled effectively by grey relational approach presented in the study. Current is found to be the most affective parameter in EDM machining using DMLS electrode. Excessive DMLS tool (electrode) wear was also reported, which limits the use of DMLS tool for EDM machining and it has been found out that porosity (which was about 20 per cent) was one of the primary cause. Research limitations/implications This paper was focused on understanding the effects of important EDM parameters on three performance characteristics (TWR, MRR and surface roughness). While this study identifies that DMLS electrode wear rate is high and porosity could be one of the main cause, presently it does not cover the investigations on reducing the porosity level and its implications. Practical implications The DMLS material had shown huge potential to be used as EDM electrode. The current investigation established a structured experimental approach to understand the effects of EDM parameters on multi response characteristics. The results derived from this study helps to focus future research on two aspects including enriching the copper content and reducing the porosity level, thereby the benefits of lead time reduction in EDM electrode making could be realized. Originality/value The previous research attempts were not focussed on optimising the EDM machining process using rapid tooling electrodes. With the best of author's knowledge none of the researchers have reported these aspects especially for DMLS electrodes. Application of grey relational analysis for performance evaluation of rapid tooling‐based EDM electrodes (DMLS electrodes) appear to be completely new.

Suitability of electrical discharge machining debris particles for usage as a powder for selective laser melting: an explorative study

Characterization and Microstructure of Recycled Eroded Particles from Die-Sink Electro Discharge Machining of H11 Alloy for Applicability in Additive Manufacturing

Research of the possibility of using an electrical discharge machining metal powder in selective laser melting

Electrical Discharge Machining Electrodes Manufactured via Selective Laser Sintering Technique Using New Composite Materials

Study on Particle Size Distribution of Debris in Electrical Discharge Machining of Deep Narrow Slots

Investigating particle morphology, quality, flowability and performance of abrasive-grinding based powders for directed energy deposition

Advanced Electric Discharge Machining of Stainless Steels: Assessment of the State of the Art, Gaps and Future Prospect

Selective laser sintering of Mo-CuNi composite to be used as EDM electrode

Research on EDM Performance of Renewable Dielectrics under Different Electrodes for Machining SKD11

Powder degradation as a consequence of laser interaction: A study of SS 316L powder reuse on the laser directed energy deposition process

Die-sinking EDM of Al6061-T6: interactions between process parameters, process performance, and surface characteristics

Powder Mixed Dielectric: An Approach for Improved Process Performance in EDM

Analysis of Particle Size and Concentration in Die Sinking Electric Discharge Machining

Influence of 4-dodecylbenzenesulfonic acid as a surfactant on a graphite-based dielectric in powder mixed electric discharge machining

An Analysis of the Discharge Mechanism in Electrochemical Discharge Machining of Particulate Reinforced Metal Matrix Composites

An Orthogonal Experimental Analysis of Electrical Discharge Machining of Particle Reinforced Metal Matrix Composites with Concavo-Convex Electrode

Performance analysis of tool electrode prepared through laser sintering process during electrical discharge machining of titanium

Optimization of EDM machining parameters using DMLS electrode

Sustainable electric discharge machining using alumina-mixed deionized water as dielectric: Process modelling by artificial neural networks underpinning net-zero from industry

Experimental research on EDM-milling of sintered NdFeB

Investigation on the Effect of Different Dielectric Fluids During Powder Mixed EDM of Alloy Steel