Abstract:Additive manufacturing (AM) of biomedical materials provides enormous opportunities to fabricate multifunctional and structurally designed frameworks for tissue engineering, such as dental implants and bone substitutes. Despite several advantages of the binder jet 3D printing technology over other AM methods, for example, no limitations in materials selection, high materials recycling efficiency, no thermal stress development, no need to support materials, and the possibility of fabrication of printing functionally graded materials, the fabrication of biomedical-grade titanium alloys with high-density, fine microstructure, and low pickup of impurities is still challenging. This work presents the effects of powder particle size and 3D printing conditions on the microstructural features and mechanical properties of Ti-6Al-4V alloy. The formation of large and inter-aggregate pores during binder jetting is demonstrated and discussed. Design and selection of particle size distribution with a mean diameter of ~20 μm and large span and positive skewness are proposed to minimize binder-induced powder aggregation and fabricate green parts with a density of 65±1% PFD (pore-free density). Dilatometric studies under a partial pressure of argon (0.1 bar) determine that sintering just above the α/β transus temperature (~980 °C) provides a high strain rate to remove pores, but high-temperature sintering (≥1250 °C) is required to attain 97% PFD. The successful fabrication of high-density Ti-6Al-4V parts (≥96% PFD) with the microstructure comparable to metal injection molding (MIM) titanium parts (≈100 μm α grains + β lattes) is demonstrated. The tensile strength and elongation values fall in the range of 880±50 MPa and 6±2% (depending on the processing condition), which is comparable with metal injection molded parts and superior to the laser powder bed fusion technology concerning ductility. The content of carbon (<0.02 wt.%) and nitrogen (0.01 wt.%) also falls in the standard region of metal injection molding. However, oxygen pickup during sintering moderately increases the oxygen content (for 30–50%) over the standard level. The concentration of interstitials entrapped in the metal is comparable to that of parts manufactured by the powder bed fusion process, but the mechanical properties are better matched with the commercial titanium alloy. The fabrication of the titanium alloy as per the ASTM F2885 standard provides an excellent opportunity for the binder jetting process to develop custom-made biomaterials.

Paste-based 3D printing of metallic materials: effect of binders and precursor sizes

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Fabrication of 3D Printed Metal Structures by Use of High-Viscosity Cu Paste and a Screw Extruder

Fused filament fabrication of stainless steel structures - from binder development to sintered properties

Development of paste extrusion-based metal additive manufacturing process

Sustainable metal-infused polymer feedstock compatible with low-cost metal sinter-based 3D printing

Photopolymerization of Stainless Steel 420 Metal Suspension: Printing System and Process Development of Additive Manufacturing Technology toward High-Volume Production

3D printing of metals using biodegradable cellulose hydrogel inks

Preparation of optimum degreasing–sintering process for metal–polymer blending low temperature 3D printing

Effect of Preprocessing Temperature On the Recycling of Waste Direct Metal Laser Sintering Powder

Low cost 3D printing of metals using filled polymer pellets

Direct 3D Printing of Low Melting Point Alloy Via Adhesion Mechanism

Microstructural development during additive manufacturing of biomedical grade Ti-6Al-4V alloy by three-dimensional binder jetting: material aspects and mechanical properties

Influence of Binder Composition and Material Extrusion (MEX) Parameters on the 3D Printing of Highly Filled Copper Feedstocks

Systematical investigation of rheological performance regarding 3D printing process for alkali-activated materials: Effect of precursor nature

3D printing of metal parts using a highly-filled thermoplastic filament

Development of Flexible and Partly Water-Soluble Binder Systems for Metal Fused Filament Fabrication (MF3) of Ti-6Al-4V Parts

Effect of bimodal powder on densification and mechanical properties of 316L stainless steel fabricated by binder jet 3D printing

Towards additive manufacturing of magnesium alloys through integration of binderless 3D printing and rapid microwave sintering

Printability and physical properties of iron slag powder composites using material extrusion-based 3D printing

Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals