Abstract:Ultra-high performance concrete (UHPC) is characterized by its ultra-high strength and durability, making it suitable for use in large-span bridges, super high-rise buildings, and other special structures. These types of structures often have high requirements for crack control, making the exploration of UHPC's fracture mechanics properties of significant importance. Therefore, this paper sets up four steel fiber contents (0%, 0.6%, 1.2% and 1.8%) and four strain rates (10-5/s, 10-4/s, 10-3/s and 10-2/s), totaling 16 working conditions. The hydraulic servo system combined with digital image correlation (DIC) technology was used to conduct fracture mechanics tests on UHPC three-point bending beams. The test results show that the unstable fracture load of UHPC increases with the increase of strain rate and steel fiber content, and increasing the steel fiber content can enhance the strain rate effect of UHPC to a certain extent. Additionally, combined with the J-criterion model, this study proposed a dynamic criterion for the unstable fracture load of UHPC considering the influence of steel fiber content. The initial fracture toughness, unstable fracture toughness, and fracture energy of UHPC are significantly more affected by steel fiber content than by strain rate. Through DIC technology, the analysis of UHPC crack propagation shows that UHPC without steel fibers experiences rapid crack expansion in the Pre-90% to Peak stage, with less influence from the strain rate. However, UHPC with steel fibers exhibits a more uniform crack growth rate, with the crack emergence phase gradually lagging as the strain rate increases. For UHPC without steel fibers, the crack opening displacement (COD) at the unstable fracture load point surges suddenly, while the COD development in UHPC with steel fibers is slower. At lower strain rates, an increase in steel fiber content leads to an earlier sudden increase phase in UHPC's COD; at higher strain rates, the influence of steel fiber content on the sudden increase phase of UHPC's COD is more scattered. The research results of this paper provide a theoretical basis for the calculation and analysis of the dynamic response of UHPC structures under seismic loads.

Development of the strain field along the crack in ultra-high-performance fiber-reinforced concrete (UHPFRC) under bending by digital image correlation technique

Study on Surface Cracking of Corroded Reinforced Concrete Based on DIC Method

Analysis of the flexural properties of ultra-high-performance concrete consisting of hybrid straight steel fibers

Application of the J-Integral and Digital Image Correlation (DIC) to Determination of Multiple Crack Propagation Law of UHPC under Flexural Cyclic Loading

Steel Rebar Effect on Tensile and Cracking Behavior of UHPFRC Based on Direct Tensile Tests and Digital Image Correlation

Investigation of fatigue crack propagation behavior in steel fiber-reinforced ultra-high-performance concrete (UHPC) under cyclic flexural loading

Study on the Dynamic Fracture Mechanical Properties of Ultra High-Performance Concrete under the Influence of Steel Fiber Content

Study of Flexural and Crack Propagation Behavior of Layered Fiber-Reinforced Cementitious Mortar Using the Digital Image Correlation (DIC) Technique

Time-varying Relative Displacement Field on the Surface of Concrete Cover Caused by Reinforcement Corrosion Based on DIC Measurement

Concrete Stress Intensity Factor Evaluation With a Digital Image Correlation Approach

A New Flexural Strength Model of CFRP-strengthened RC Beams with Intermediate Crack Induced Debonding Failure

In situ characterization of the flexural behavior and failure mechanism of 2D needle-punched carbon/carbon composites by digital image correlation

FRACTURE PARAMETERS STUDY AND APPLICATION OF ULTRA HIGH PERFORMANCE FIBER REINFORCEMENT CONCRETE

Dynamic split tests of UHPFRC discs and failure mechanism analysis based on μXCT images

Crack Propagation Behavior of Ultra-High-performance Concrete (UHPC) Reinforced with Hybrid Steel Fibers under Flexural Loading

Experimental Study on the Fracture Process Zone Characteristics in Concrete Utilizing DIC and AE Methods

Experimental study on fracture and fatigue crack propagation processes in concrete based on DIC technology

STUDY ON THE FIBER-REINFORCED CONCRETE PULL-OUT TEST USING DIGITAL IMAGE CORRELATION METHOD

Evaluation of concrete fracture behavior based on digital image correlation

Quantitative Analysis of Steel Fibers on UHPFRC Uniaxial Tensile Behavior Using X-CT and UTT

Relation Between Electrically Conductive Properties and Flexural Behaviors of Ultra‐high‐performance Concrete