Abstract:Cellular lattices with architectural intricacy or metamaterials have gained a substantial amount of attention in the past decade due to the recent advances in additive manufacturing methods. The lattice topology controls its physical and mechanical properties; therefore, the main challenge is selecting the appropriate lattice topology for a desired function and application. In this work, we comprehensively study the topology–property relationship of three classes of polymer metamaterials based on triply periodic minimal surfaces (TPMS) of sheet/shell and ligament types, and other types of well-known strut-based lattices. The study uses a holistic approach of designing, additive manufacturing, microstructural characterization, and compressive uniaxial mechanical testing of these polymer lattices that are 3D-printed using the laser powder bed fusion technique known as selective laser sintering (SLS). In total, 55 lattices with different topologies and relative densities were 3D-printed and tested. Printing quality was assessed using scanning electron microscopy and micro-computed tomography. The extracted mechanical properties of elastic modulus, yield strength, plateau strength, and energy absorption are thoroughly compared between the different lattice architectures. The results show that all the investigated ligament-based TPMS polymer lattices exhibit bending-dominated elastic and plastic behavior, indicating that they are suitable candidates for energy absorbing applications. The sheet-based TPMS polymer lattices, similarly to the well-known Octet-Truss lattice, exhibited an elastic stretching-dominated mode of deformation and proved to have exceptional stiffness as compared to all other topologies, especially at low relative densities. However, the sheet-based TPMS polymer lattices exhibited a bending-dominated plastic behavior which is mainly driven by manufacturing defects. Overall, however, sheet-based TPMS polymer lattices exhibited the best mechanical properties, followed by strut-based lattices and finally by ligament-based TPMS lattices. Finally, it is depicted that at high relative densities, the mechanical properties of lattices of various architectures tend to converge, which implies that the topological effect is more significant at low relative densities. Generally, this study provides important insights about the selection of polymer mechanical metamaterials for various applications, and shows the superiority of TPMS-based polymer metamaterials as compared to several other classes of polymer mechanical metamaterials.

Effect of Porosity and Cell Topology on Elastic-Plastic Behavior of Cellular Structures

Tension-compression asymmetric mechanical behaviour of lattice cellular structures produced by selective laser melting

Quasi-static Compression and Compression-Compression Fatigue Behavior of Regular and Irregular Cellular Biomaterials

Modeling of the effect of local material imperfection to the structural mechanical property variability of 2D finite-size cellular structures

Experimental investigation on the mechanical properties of Ti6Al4V cellular structures produced with selective laser melting: Effects of rib thickness, unit cell type and orientation

Elastic properties and compressive mechanical behaviour of closed-cell porous materials: Effect of microstructural morphology

Additively Manufactured Open-Cell Porous Biomaterials Made from Six Different Space-Filling Unit Cells: The Mechanical and Morphological Properties

Viscoelastic Behavior of Cellular Biomaterials Based on Octet-Truss and Tetrahedron Topologies

Investigating internal architecture effect in plastic deformation and failure for TPMS-based scaffolds using simulation methods and experimental procedure

Compressive properties and deformation mechanism of selective laser melting of Ti6Al4V porous femoral implants based on topological optimization

Effects of porosity gradient pattern on mechanical performance of additive manufactured Ti-6Al-4V functionally graded porous structure

Modeling and analysis of material anisotropy-topology effects of 3D cellular structures fabricated by powder bed fusion additive manufacturing

Effect of porosity variation strategy on the performance of functionally graded Ti-6Al-4V scaffolds for bone tissue engineering

Effect of porous defects on mechanical behavior of functionally graded materials

The Mechanical Behavior of Porous Metal Fiber Sintered Sheets

On the Morphological Deviation in Additive Manufacturing of Porous Ti6Al4V Scaffold: A Design Consideration

M-Voronoi and other random open and closed-cell elasto-plastic cellular materials: Geometry generation and numerical study at small and large strains

On the Effect of Lattice Topology on Mechanical Properties of SLS Additively Manufactured Sheet-, Ligament-, and Strut-Based Polymeric Metamaterials

Experimental and numerical study of the compressive fatigue behavior of a Ti6Al4V mapped rhombioidal dodecahedral structure fabricated by electron beam melting

Modeling Mechanical Properties of Titanium Scaffolds with Variable Microporosity

Three-dimensional elastic properties of open-cell porous structures: Analytic and finite element modelling