Abstract:Thin-gauge non-oriented silicon steel with high strength was successfully processed using strip casting. Texture evolution and strengthening mechanism via nanoscale Cu-rich precipitates were studied to fundamentally understand the balanced combination of magnetic properties and mechanical properties. Coarse equiaxed grains with average size of ∼190 μm and relatively random texture were formed in the as-cast strip, which contributed to the inhomogeneous deformation, resulting in high density of shear bands. Exact Cube was retained from the initial Cube texture and new Goss was formed during the heavy rolling process in the 0.20 mm cold rolled sheet, which promoted relatively strong Cube and Goss texture after recrystallization annealing. The 0.20 mm annealed sheet exhibited high magnetic induction of 1.709 T, which corresponds to the high texture factor of 0.5. The total iron losses were significantly reduced with decrease in thickness, and the P1.5/50, P1.0/400, and P1.0/1000 in 0.20 mm sheet were as low as 2.63, 15.17 and 55.63 W/kg, respectively, which showed a good match between magnetic induction and iron loss. During the aging process, both the magnetic induction and total iron loss exhibited relatively good stability. With increase in aging time, the yield strength first rapidly increased and then slightly decreased. In 0.20 mm sheet, peak yield strength of ∼630 MPa was obtained on aging at 550 °C for 90–120 min. The key mechanism of precipitation strengthening was attributed to the difference in modulus and coherency strain associated with high density of nanoscale precipitates of ∼5 nm. The study revealed that the nanoscale Cu-rich precipitates can be adopted as effective approach to increase the yield strength over ∼100 MPa without deteriorating iron loss in thin-gauge non-oriented silicon steel by strip casting, which guaranteed the balance of magnetic properties and mechanical properties to meet the requirements of high-speed motor.

The Significance of Microstructure and Texture on Magnetic Properties of Non‐Oriented Silicon Steel: Strip Casting versus Conventional Process

Significant effect of as-cast microstructure on texture evolution and magnetic properties of strip cast non-oriented silicon steel

Microstructure, texture and magnetic properties of strip-cast 1.3% Si non-oriented electrical steels

Microstructure Characteristics and Strengthening Behavior of Cu-Bearing Non-Oriented Silicon Steel: Conventional Process versus Strip Casting

Effect of recrystallization annealing temperature on microstructure, texture and magnetic properties of non-oriented silicon steel produced by strip casting

Microstructure, texture and magnetic properties of the semi-processed strip-cast non-oriented electrical steel

Microstructural evolution and magnetic properties in strip cast non-oriented silicon steel produced by warm rolling

Development of microstructure and texture in strip casting grain oriented silicon steel

The significance of hot rolled microstructure controlled by fine-tuning Al content to texture evolution and magnetic properties of low silicon non-oriented electrical steels

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Effect of Double Cold Rolling on Magnetic Property and Microstructure of Non-Oriented High Silicon Steel Sheets Cast by Strip Casting Process

Thin-gauge non-oriented silicon steel with balanced magnetic and mechanical properties processed by strip casting

Effects of rolling temperature on microstructure, texture, formability and magnetic properties in strip casting Fe-6.5wt% Si non-oriented electrical steel

Microstructure and texture evolution of ultra-thin grain-oriented silicon steel sheet fabricated using strip casting and three-stage cold rolling method

Fabrication of Grain-Oriented Silicon Steel by a Novel Way: Strip Casting Process

Effect of Grain Size Before Cold Rolling on Microstructure, Texture and Magnetic Properties of Ultra-Thin Low-Si Non-oriented Silicon Steel

Microstructure and texture evolution of strip casting 3 wt% Si non-oriented silicon steel with columnar structure