Abstract:"In research and development, the use of model-based methods has been established widely. In spite of the required costs and time for modelling and parameterization, the models become applicable in many steps of the design process from concept studies until parameter optimization. Particularly, during the early phase of the development of products or functions, it is necessary to keep time and cost efforts as low as possible without significantly reducing the quality of the simulation results. For the development of vehicle dynamic controls, the quality of the used models depends highly on the modelling of the wheel-road contact. Due to the reduced parameterization and calculation effort, mathematical-empirical or semi-physical approaches as well as flexible belt-ring models are preferred to simulate severe driving manoeuvres such as full braking with ABS intervention or the ISO 3888 double lane-change. The determination of the model parameters is carried out using special tire test rigs in which the tire and rim are clamped. Due to the complex experimental setup and the required infrastructure, these tests are very cost-intensive. In driving tests with real vehicle, commercially available wheel force transducers are used today. By means of force measuring elements, which are usually attached to an especially manufactured and split rim body, the transmitted forces and moments are determined while driving. A high-resolution angle sensor detects the rotation angle and the angular velocity of the wheel in order to transform the measured quantities (forces and torque at the wheel) from the rotating to the vehicle related coordinate system. At the beginning of the paper, established concepts of tire test rigs for determining the parameters of mathematical-empirical tire models will be summarized and compared with the proposed usage of a wheel force transducer in real-driving tests. This will include an estimation of the boundary conditions and the reproducibility of the measurements as well as influencing factors on the force transmission. Subsequently, the test equipment and driving manoeuvres that were carried out with the test vehicle are presented. In addition to the wheel force transducer, a 2-axis optical speed sensor is added to the test setup. Using the measured vehicle velocity and the measured wheel speed the tire slip can be calculated now. The measurement data is partly used for parameter identification of two simplified tire models according to PACEJKA and BURCKHARDT, which describe the steady-state friction coefficient slip characteristic. Since these are nonlinear tire models, a non-linear least squares algorithm is used as the mathematical optimization method. The measurement data, which was not used for the parameterization, are applied in the subsequent validation of the tire model. On the basis of the obtained results a statement about the usability of a parameterized tire model based on measurements with a wheel force transducer is made and possible extensions and suggestions for improvement are derived."

Detection and Quantification of Tire Particles in Sediments Using a Combination of Simultaneous Thermal Analysis, Fourier Transform Infra-Red, and Parallel Factor Analysis

Refinement of a microfurnace pyrolysis-GC-MS method for quantification of tire and road wear particles (TRWP) in sediment and solid matrices

Method Development for Separation and Analysis of Tire and Road Wear Particles from Roadside Soil Samples

Use of a Deuterated Internal Standard with Pyrolysis-GC/MS Dimeric Marker Analysis to Quantify Tire Tread Particles in the Environment

Automated identification and quantification of tire wear particles (TWP) in airborne dust: SEM/EDX single particle analysis coupled to a machine learning classifier

Differentiating and Quantifying Carbonaceous (Tire, Bitumen, and Road Marking Wear) and Non-carbonaceous (Metals, Minerals, and Glass Beads) Non-exhaust Particles in Road Dust Samples from a Traffic Environment

Separation and quantification of tire and road wear particles in road dust samples: Bonded-sulfur as a novel marker

Quantification of tire wear particles in road dust based on synthetic/natural rubber ratio using pyrolysis-gas chromatography-mass spectrometry across diverse tire types

Comprehensive characterization of tire and road wear particles in highway tunnel road dust by use of size and density fractionation

Abundance and distribution of tire and road wear particles in the Seine River, France

Characterization of Microplastics in Environment by Thermal Gravimetric Analysis Coupled with Fourier Transform Infrared Spectroscopy.

Development of Tire-Wear Particle Emission Measurements for Passenger Vehicles

Bioaccessibility of Organic Compounds Associated with Tire Particles Using a Fish In Vitro Digestive Model: Solubilization Kinetics and Effects of Food Coingestion

Pilot analysis of tire tread characteristics and associated tire-wear particles in vehicles produced across distinct time periods

Direct Determination of Three PAHs in Drill Cuttings Recycling Products by Solid-Surface 3D Fluorescence Coupled with Chemometrics

Investigation of the external conditions and material compositions affecting the formation mechanism and size distribution of tire wear particles

Assessing biodegradation of roadway particles via complementary mass spectrometry and NMR analyses

Methodology for the direct measurement of tire emission factors

Parameter Identification of mathematical-empirical Tire Models using Measurement Data of a Wheel Force Transducer

Characteristics of Vehicle Tire and Road Wear Particles' Size Distribution and Influencing Factors Examined via Laboratory Test

Measurement and Analysis of Brake and Tyre Particle Emissions from Automotive Series Components for High-Load Driving Tests on a Wheel and Suspension Test Bed