Abstract:Taking into consideration the seismic vulnerability and the poor energy performance of the European building stock, and the increasing socio‐economic and environmental need for integrating seismic upgrading with energy efficiency improvement, an experimental study involving the lateral load testing of full‐scale one‐story one‐bay masonry infilled RC frames and load‐bearing masonry walls was carried out in the framework of the SupERB research project aiming to investigate the efficiency of integrated seismic and energy upgrading systems. The integrated approach is based on the use of textile reinforced mortar (TRM) overlays combined either with traditional thermal insulation (extruded polystyrene, XPS) or with thermally efficient mortar incorporating phase change material (PCMs). The proposed integrated approach can be applied on the exterior face of the structure, so as to facilitate its application in real structures in the easiest possible way and with minimum disturbance to the inhabitants of the buildings. In this paper, only the structural performance of masonry‐infilled RC frames retrofitted with the proposed integrated approach is presented, while the energy benefits will be presented in a separate paper. Thus, in this paper, the structural performance of an integrated seismic and energy upgrading approach was assessed through five full‐scale one‐story one‐bay masonry infilled RC frames that were retrofitted with different schemes of TRM combined with thermal insulation materials subjected to in‐plane displacement‐controlled cyclic loading. The following parameters were investigated experimentally: the number of TRM overlays (one or two layers of TRM combined with thermal insulation), the use of thermally efficient PCM‐enhanced TRM layer in contrast to the use of conventional XPS insulation, and different retrofitting configurations (placement of the TRM in a sandwich form over and/or under the novel or the traditional insulation). From the results obtained in this study, it can be concluded that all energy and seismic upgrading systems examined have a positive impact on the response of the structural system to cyclic loading, with the ones with two layers of TRM having a better performance compared to the ones with one layer of TRM and all of them a better performance than the control specimen. The use of two layers of TRM cancels the drawback of infilled frames, which at very small drifts they reach their maximum capacity and after that they rapidly fall to the capacity of the bare frame, providing capacities above 80% of their peak capacity for drifts up to 2%. In all the tests the TRM whether it was combined with XPS or included PCMs contributed to a better distribution of the cracks in the infill and delayed premature brittle failures. The presence of the TRM had also the advantage that it remained intact throughout the tests preventing the fall of debris out of the plane of the infilled frame, both in the retrofitted and unretrofitted sides.

Precast TRC sandwich panels for energy retrofitting of existing residential buildings: full-scale testing and modelling

Seismic and energy upgrading of existing buildings—full‐scale testing of retrofitted masonry‐infilled RC frames

A retrofitting technique using steel grids for existing masonry panels: a numerical and analytical study

Energy retrofit with prefabricated timber-based façade modules: pre- and post-comparison between two identical buildings

Mechanical properties and failure patterns of sandwich panels with AR-glass textile reinforced concrete face sheets subjected to quasi-static load

Performance of Double-Skin Composite Walls with Re-Entrant Profiled Faceplates under Eccentric Compression

Seismic and Energy Integrated Retrofitting of Existing Buildings with an Innovative ICF-Based System: Design Principles and Case Studies

Lightly reinforced concrete walls in formwork blocks for the combined seismic and energy retrofit of masonry structures

Out-of-plane performance of structurally and energy retrofitted masonry walls: geopolymer versus cement-based textile-reinforced mortar combined with thermal insulation

An Innovative, Lightweight, and Sustainable Solution for the Integrated Seismic Energy Retrofit of Existing Masonry Structures

Combined Flexural and Shear Strengthening of RC T-Beams with FRP and TRM: Experimental Study and Parametric Finite Element Analyses

Integrated Seismic and Energy Retrofitting System for Masonry Walls Using Textile-Reinforced Mortars Combined with Thermal Insulation: Experimental, Analytical, and Numerical Study

Analytical modeling of textile reinforced concrete (TRC) sandwich panels: Consideration of nonlinear behavior and failure modes

Parametric study on the in-plane performance of a steel frame retrofit solution for URM buildings using DEM

Development of Concrete Façade Sandwich Panels Incorporating Phase Change Materials

Thermische Lastansätze für Fertigteil‐Sandwichfassaden unter Berücksichtigung moderner Bauweisen

Cross‐laminated timber for seismic retrofitting of RC buildings: Substructured pseudodynamic tests on a full‐scale prototype

A simplified analytical approach for CLT-based seismic retrofit of existing reinforced concrete structures

Mechanical performance of prefabricated lightweight steel-foamed ceramsite concrete wall panels: Experimental and theoretical investigations

A multilayer panel in cork and natural phase change materials: thermal and energy analysis

Flexural performance of novel ECC-RC composite sandwich panels