Abstract:Relevance In the Russian Federation, 82 % of oil is produced using Electric Submersible Pumps (ESP), while only 63 % of wells are equipped with such pumps. Since more than half of the operating wells are equipped with ESP, developing methods to reduce operating costs for these wells is a rational and logical allocation of human, material, and financial resources. One method to increase the profitability of oil production from low- and medium-flow rate wells is to transition a well equipped with ESP from continuous operation to intermittent operation, specifically cyclic operation. Intermittent operation reduces energy consumption by up to 40 % and increases oil production by 3 % due to partial gravitational separation of the produced fluid during accumulation. However, the negative effect of transitioning to intermittent operation is reflected in the reduction of the average runtime before failure due to a decreased ESP hydroprotection resource, accelerated wear of the pump unit thrust bearings, and intermediate radial bearings. The cause of these negative effects is the increased vibration level during intensive startup. One way to address these issues is transitioning from the existing scalar open-loop control system to a vector sensorless control system for the ESP. To implement such a system, it is necessary to obtain information about the vector of the ESP state variables. A promising approach to obtaining information about the ESP state involves creating observers based on explicit mathematical models. To create an observer for the state variables, mathematical models for each component of the studied system must be developed and combined into a unified system. When measuring currents and voltages at the output of the step-up transformer, the studied system will be an electric complex «Cable Line — Induction Motor». To implement this observer, it is necessary to determine the parameters of the equivalent circuit of the studied complex. Based on the above, developing a methodology for identifying the parameters of the equivalent circuit of the electric complex «Cable Line — Induction Motor» when measuring currents and voltages on the surface is a timely and relevant task. Solving this task will create prerequisites for the implementation of a vector control system for the ESP, increasing the reliability of the ESP during intermittent operation, and consequently, increasing the profitability of oil production from low- and medium-flow rate oil wells. Aim of research To develop and experimentally confirm the effectiveness of a methodology for assessing the parameters of the electric complex «Cable Line — Induction Motor» based on the balance of consumed power. Research methods Analysis of literary sources, system analysis, mathematical modeling, experimental research. Results The effectiveness of the methodology for assessing the parameters of the electric complex «Cable Line — Induction Motor» based on the balance of consumed power has been experimentally tested and confirmed.

Improving the Energy Efficiency of the Sucker-rod Pump via Its Optimal Counterbalancing

Design, Modeling, and Pressure Control of a 300-Kw-class Hydraulic Pump/motor Loading System with Energy Regeneration

A New Reactive Power-Based Sensorless Control Strategy For Five-Phase Induction Motor With Non-Sinusoidal Power Supply

An Investigation in Performance of a Variable-Speed-Displacement Pump-Controlled Motor System

Development of Parallel-Connected Pump–valve-Coordinated Control Unit with Improved Performance and Efficiency

Kinematic and Dynamic Analysis of Eccentric Balanced Positive Torque Pumping Unit

Optimization of a Centrifugal Pump to Improve Hydraulic Efficiency and Reduce Hydro-Induced Vibration

A sensorless efficiency-optimizing vector control scheme for an induction motor drive

Improving Reliability of Pumps in Parallel Pump Systems Using Particle Swam Optimization Approach

The Design and Analysis of a Hydro-Pneumatic Energy Storage Closed-Circuit Pump Control System with a Four-Chamber Cylinder

Investigation on the Cross Power Control of Axial Piston Double Pump Based on the Virtual Prototype

Advanced Valves and Pump Coordinated Hydraulic Control Design to Simultaneously Achieve High Accuracy and High Efficiency.

METHODOLOGY FOR EVALUATING PARAMETERS OF THE ELECTRICAL COMPLEX «CABLE LINE — INDUCTION MOTOR» BASED ON POWER CONSUMPTION BALANCE

Optimal Rotor Design and Analysis of Energy-Efficient Brushless DC Motor-Driven Centrifugal Monoset Pump for Agriculture Applications

Automatic optimization of centrifugal pump based on adaptive single-objective algorithm and computational fluid dynamics

Energy Efficient Control of an Induction Machine under Load Torque Step Change

Design and Optimization of Synchronous Motor Using PM Halbach Arrays for Rim-Driven Counter-Rotating Pump

An Analysis of Energy-saving and Simulation on Variable Torque Balance of Beam Pumping Unit

Optimal Control of Induction Motor for Photovoltaic Water Pumping System

Artificial Intelligence Enabled Energy-Saving Drive Unit With Speed and Displacement Variable Pumps for Electro-Hydraulic Systems

Practical Model for Energy Consumption Analysis of Beam Pumping Motor Systems and Its Energy-Saving Applications