Abstract:This paper presents the results of a numerical study on a supercritical CO2 (SCO2) turboshaft cooling device by considering heat transfer and hydrodynamics. A micro-cooling device with a radius clearance of 50 micron and a nozzle diameter of 4 mm was designed and used to investigate the heat transfer characteristics of a micro-spacing impinging and gas film dynamics. Sixteen nozzles ( N = 16) are equally spaced around the shaft in single or double rows. Investigations include journal speed- and eccentricity-dependent forward and cross-coupled force coefficients, and the effects of nozzle layouts and mass flow rate on the heat transfer efficiency. Analysis of the correlation coefficient shows that the gas density in the radial clearance is the dominant factor affecting the convective heat transfer performance, while the fluid velocity is a secondary factor. And the cooling efficiency (mass flow utilization rate) at low cooling pressure ( p s < 0.7 MPa) is significantly greater than that at high cooling pressure ( p s > 0.7 MP). In addition, considering the structure alone, a dual-row cooler exhibits a higher average Nusselt number, also registers a higher mass flow rate at the same pressure. Once the shaft is heated only one end, the difference in effectiveness between single- and dual-row cooling is not significant, so coolers with a single-row configuration should be preferred. Then, experimental values for the temperature of the heated rotor are provided under specific cooling airflow conditions. Dynamic analysis results show that the force coefficient of the single-row configuration is more dependent on the journal rotation speed and eccentricity ratio, and exhibits a negative direct stiffness coefficient at higher inlet pressure and journal rotation speed. Moreover, cross-coupled terms (stiffness coefficient) generally have a more explicit variation tendency than direct terms, and are more sensitive to changes in shaft speed and eccentricity. Small clearance cooling is a relatively complex technology aimed to improve heat dissipation efficiency in gas cooling devices while minimizing the effect of hydrodynamic pressure. Comparing the gas force coefficients of different journal speeds reveals a drastic increase in the effect of hydrodynamic pressure when the journal is eccentric. The cooler may be considered for operation with compliant support (such as bump foil) to generate additional damping and appropriately compensate for the eccentricity of the rotor.

Numerical Study of Radiation Heat Transfer for a Supercritical CO2 Turbine Linear Cascade

Experimental and Numerical Study on Thermal Hydraulic Performance of Trapezoidal Printed Circuit Heat Exchanger for Supercritical CO2 Brayton Cycle

Experimental and Numerical Investigation on the Dynamic Characteristics of a Lab-Scale Transcritical CO2 Loop

Numerical Study on Rotor Cooling of Turbine in Supercritical Carbon Dioxide Cycle

Numerical Study on Heat Transfer Characteristic of CO2 in Helical Tube at Supercritical Pressure

Thermal Management and Dynamic Performance of a Cooler Design for the Supercritical CO2 Turbine Shaft Cooling

Experimental and Numerical Investigation of Effect of Inclination on sCO 2 Heat Transfer in a Circular Pipe

Numerical Investigation on Turbulent Heat Transfer of Supercritical CO2 in a Helically Coiled Tube

Aerodynamic Design and Numerical Analysis of a Radial Inflow Turbine for the Supercritical Carbon Dioxide Brayton Cycle

Computational Study of Heat Exchange and Thermal Oxidative Coking of Supercritical-Pressure Kerosene with Compressed Air in Counterflows

Investigation of the Steam-Cooled Blade in a Steam Turbine Cascade

Numerical Study on Flow Structure and Heat Transfer of Supercritical CO2 in Tubes with Different Inclination Angles

Design a cooling pillow to support a high-speed supercritical CO2 turbine shaft

Performance Analysis of Heat Exchangers and Integrated Supercritical CO2 Brayton Cycle for Varying Heat Carrier, Cooling and Working Fluid Flow Rates

Flow and Heat Transfer Characteristics of Supercritical CO2 in a Natural Circulation Loop

Numerical research on the heat transfer and pressure drop of supercritical CO2 in spiral wound tubes

Supercritical CO 2 flow and heat transfer through tapered horizontal mini-tubes: Parametric analysis and optimization study

NUMERICAL STUDIES ON THERMAL-HYDRAULIC PERFORMANCE AND CORRELATIONS OF PRINTED CIRCUIT HEAT EXCHANGER WITH ZIGZAG CHANNEL FOR SUPERCRITICAL CO<sub>2</sub> POWER CYCLE

Thermodynamic and Economic Investigations of Transcritical CO2-cycle Systems with Integrated Radial-Inflow Turbine Performance Predictions

Flow resistance analysis of non-isothermal supercritical CO2

Corrosion of Potential First Stage Blade Materials in Simulated Supercritical CO2