Abstract:Boiling is widely employed in practical applications due to its excellent heat-transfer characteristics. To meet the ever-increasing demand of heat dissipation, boiling optimization is an important topic in heat transfer research. In this work, saturated pool boiling experiments were conducted on thin copper wires with superhydrophobic micropatterns. The investigation was conducted on a thin copper wire patterned with superhydrophobic sites. The wire was 150 mu m in diameter and 85 mm in length. Briefly, the wire was first uniformly coated with a photoresist. The patterns were then created by a means of soft lithography using with a photo-plotted mask. Afterwards, an electroless galvanic deposition method was applied to coat a thin superhydrophobic layer onto the exposed copper patterns, by consecutively immersing the wire in AgNO3 and heptadecafluoro-1-decanethiol (HDFT) solutions. Finally, the remaining photoresist on the wire was removed, leaving the superhydrophobic micropatterns coated onto the copper surface. In most tests, the patterns were 100 mu m wide with 3-mm separation distance. De-ionized (DI) water was used as the working fluid, and boiled and degassed for 30 minutes in the chamber prior to the measurement. The testing wire was also heated in the chamber to degas. A high-speed CCD camera up to 30000 frames per second was mounted on a microscope for continuous imaging of bubble formation. Optical illumination was achieved by a fiber optic illuminator system. The superhydrophobic pattern lowered the superheat for bubble nucleation. Larger pattern area led to lower superheat. The superheat dropped from 7.3 to 4.2 degrees C when the pattern width increased from 20 to 1000 mu m. When bubble grew on the pattern site, there was a neck region connecting the detaching bubble and the pattern. As the bubble detached with the breakage in the middle of the neck region, a residual bubble still remained, which served as the embryo for the next cycle. However, the existence of the embryo didn't significantly facilitate the bubbling process itself, as compared to that over the bare copper region. The bubble interactions on the superhydrophobic micropatterns were studied. Different boiling regimes were observed as the heat flux increased: (1) Isolated on-pattern bubbling regime; (2) on-pattern coalescence regime; (3) cross-pattern coalescence. The superhydrophobic micropatterns played dominant roles in bubble formation as well as the bubble interactions. The bubbles on the bare copper surface could not grow independently. Heat transfer efficiency was enhanced by 40%-60% as compared to that on the bare copper wire. The wettability patterning on the wire significantly lowered the nucleation temperature, while increasing the bubble density. However, no appreciable change over the bubble detachment volume and frequency on single nucleation site was observed. Based on the observed bubble parameters, the nucleate boiling heat transfer can be predicted and calculated by using the heat flux partitioning model. The heat transfer comprised of three components: Natural convection, latent heat of bubble growth, and transient conduction caused by bubble growth and detachment. The third mechanism was found to be the major contributor to the heat transfer in the studied nucleate boiling on the patterned wires. Future work is needed to clarify the optimal distribution of the patterns, which is supposed to be related to the wire geometry, conductivity and capacity.

Distilled water and ethyl alcohol boiling heat transfer on selected meshed surfaces

Enhanced pool boiling heat transfer during quenching on micro/nanostructured wicking surface: effects of submicron-scale substructures

Analysis of Enhanced Pool Boiling Heat Transfer on Laser—Textured Surfaces

Heat Transfer Enhancement on Multilayer Wire Mesh Coatings and Wire Mesh Coatings Combined with Other Surface Modifications—A Review

Enhanced pool boiling heat transfer characteristics on microstructured copper surfaces coated with hybrid nanofluid

Nanosecond Laser-Textured Copper Surfaces Hydrophobized with Self-Assembled Monolayers for Enhanced Pool Boiling Heat Transfer

Visualization Study of Pool Boiling on Polished and Porous Coated Surfaces for Deionized Water and Al2O3-Water Nano-Fluids

An experimental investigation of pool boiling augmentation using four-step electrodeposited micro/nanostructured porous surface in distilled water

Surface Modification Utilizing Photolithography Process for Pool Boiling Enhancement: An Experimental Study

Experimental Investigations Of Pool Boiling Heat Transfer On Horizontal Plate Sintered With Metallic Fiber Felt

Effects of composite coatings on pool boiling performance characteristics in demineralized water

Comparative Experimental Study on Pool Boiling Performance of Porous Coating and Solid Structures with Reentrant Channels

Enhanced Boiling Heat Transfer on Composite Porous Surface

Experimental investigation on pool boiling heat transfer enhancement using reticular bi-conductive surfaces

Physical dealloying for two-phase heat transfer applications: pool boiling case

Nucleate Boiling on Thin Copper Wires with Micropatterned Superhydrophobic and Hydrophilic Areas

Experimental Study on the Flow Boiling (Two-Phase) Heat Transfer of High-Density Micro-/Nano-Porous Copper-Alumina-Copper Nano-composite-Coated Surfaces

Hydrophilic and Hydrophobic Nanostructured Copper Surfaces for Efficient Pool Boiling Heat Transfer with Water, Water/Butanol Mixtures and Novec 649

Laser Treatment of Surfaces for Pool Boiling Heat Transfer Enhancement

Material And Geometry Effects Of Wire Surface Coating On Heat Transfer In He Ii Bath

Pool Boiling Enhancement Via Surface Engineering for Thermal Management