Abstract:In this study, the surface modification of titanium plates was performed using in situ nitriding via plasma-enhanced chemical vapor deposition to improve the conductivity and corrosion resistance of the plates. A series of titanium nitride (TiN) coatings were synthesized at different nitriding temperatures and durations. The influence of nitriding temperatures and durations on the surface morphology, hydrophobicity, interfacial conductivity, and corrosion resistance of the as-prepared coatings was investigated. The results indicated that faster growth and larger particle size of TiN are observed at higher temperatures. However, lower temperatures are unfavorable for surface reactions; thus, the coating cannot entirely cover the titanium substrate. Moreover, a shorter nitriding time results in irregular nanogrowth nuclei on the surface, leading to an uneven coating and bare titanium substrate. Conversely, longer nitriding time encourages the continuous accumulation of TiN nanoparticles and forms a uniform coating of the titanium substrate but decreases the flatness because of the stacking of the coatings due to the long nitriding time (120 min). The TiN coating prepared by nitriding at 650 °C for 90 min (TiN-650-90) is relatively compact and smooth with the composition of TiN0.26 and has an increased water contact angle of 105.4°. The change from hydrophilicity to hydrophobicity in TiN is beneficial to fuel cell water resistance. At a loading pressure of 1.5 MPa, the contact resistances of the coatings prepared at a nitriding time of 60 min can satisfy the U.S. Department of Energy requirement of less than 10 mΩ·cm2. Despite a contact resistance of 13.2 mΩ·cm2 for the TiN-650-90 coating, the contact resistance decreases with increasing loading pressure and is stable at 6.5 mΩ·cm2 under a loading pressure of 2.75 MPa. The corrosion current density of the TiN-650-90 coating is 0.56 μA·cm−2, and the corrosion potential positively shifts from −0.37 to −0.05 V at room temperature. The corrosion current density tested in the simulated operating environment of fuel cells is higher than that at room temperature but much lower than that of titanium (4.2 μA·cm−2). Furthermore, the current density is stable at 0.67 μA·cm−2 and at a −0.1 V constant potential, indicating superior corrosion resistance and stability than titanium. The titanium bipolar plates modified by this method exhibit the advantages of relatively low deposition temperature, quick deposition speed, and good hydrophobicity, conductivity, and corrosion resistance. This work can pave the way for efficient surface modification of metal bipolar plates.

Anodic plasma-electrolyte modification of Fe and Ti-based alloys

Multiple Needle Cathodes Plasma Surface Alloying of Ti6Al4V with W-Mo-C-N

Plasma Nitridation and Mechanical Properties of Pure Titanium Casts

Surface Modification of Titanium by Oxidation Followed by Electrospark Alloying with a Graphite Electrode

Tribological and corrosion properties of β-TiNb alloy modified by plasma electrolytic oxidation: Evaluation of the synergistic effect of composition and processing time through statistical evaluation

Investigation of the properties of oxide coatings on titanium alloys obtained by plasma electrolytic oxidation

Improved Seawater Corrosion Resistance of Electron Beam Melting Ti6Al4V Titanium Alloy by Plasma Nitriding

Electrochemical, Tribological and Biocompatible Performance of Electron Beam Modified and Coated Ti6Al4V Alloy

Improvement of the Ti-6Al-4V Alloy’s Tribological Properties and Electrochemical Corrosion Resistance by Nanocomposite TiN/PEEK708 Coatings

Electrospark Deposition of Ti – Al – Cr – B Coatings on Titanium Alloy VT3-1

Characterization and electrochemical behavior of a multilayer-structured Ti–N layer produced by plasma nitriding of electron beam melting TC4 alloy in Hank's solution

Tribological Behaviors of Electroless Nickel-Boron Coating on Titanium Alloy Surface

High efficient co-doping in plasma electrolytic oxidation to obtain long-term self-lubrication on Ti6Al4V

Effect of Surface Modification on Tribological Properties of VT22 and Ti-5553 Titanium Alloys

Surface Modification of Chromium–Nickel Steel by Electrolytic Plasma Nitriding Method

Surface Characterization and Electrochemical Studies of Biomedical Niti Alloy Coated with Tin by Piiid

Enhanced corrosion resistance and hemocompatibility of biomedical NiTi alloy by atmospheric-pressure plasma polymerized fluorine-rich coating

Evaluating the Performances of Surface-Modified Titanium Bipolar Plates Using in Situ Nitriding by Plasma-Enhanced Chemical Vapor Deposition

Increase in corrosion resistance of carbon steel surface due to plasma surface modification with powder mixtures of NiCrBSi alloy and chrome carbide

Low-Temperature Plasma Surface Modification of Medical Grade Austenitic Stainless Steel to Combat Wear and Corrosion

Enhancement of Wear and Corrosion Resistance of Ti6Al4V Alloy through Hollow Cathode Discharge-Assisted Plasma Nitriding