Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Temperature dependence of the interfacial bonding characteristics of silica/styrene butadiene rubber composites: a molecular dynamics simulation study

Study on structures, dynamics and mechanical properties of styrene butadiene rubber (SBR)/silica interfaces: A fully atomistic molecular dynamics

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Modeling Percentages of Cohesive and Adhesive Debonding in Bitumen-Aggregate Interfaces Using Molecular Dynamics Approaches

Molecular dynamic study of radiation-moisture aging effects on the interface properties of nano-silica/silicone rubber composites

Molecular dynamics simulation of glass transition and thermal stability of novel silicone elastomer and its nanocomposites

Study on the diffusion behaviour of styrene-butadiene rubber modifier and asphalt components based on molecular dynamics simulation

Quantification of interfacial structure at nanoscale and its relationship with viscoelastic glass transition of SiO2/elastomer nanocomposites

Adjusting silica/rubber interfacial interactions and properties via the click reactions between liquid polybutadiene and silane

Kinetics of the Glass Transition of Silica-Filled Styrene-Butadiene Rubber: The Effect of Resins

Effect of Interface on Bulk Polymer: Control of Glass Transition Temperature of Rubber

Study of Styrene Butadiene Rubber Reinforced by Polybutadiene Liquid Rubber-Modified Silica

A combined simulation and experiment study on polyisoprene rubber composites

Molecular Dynamics Simulations Probing the Effects of Interfacial Interactions on the Tribological Properties of Nitrile Butadiene Rubber/Nano-SiO 2 under Water Lubrication

Molecular Dynamics Simulation on the Heat Transfer in the Cross-Linked Poly(dimethylsiloxane).

Preparation and Dynamic Mechanical Properties of Copolymers Based on Butadiene, Isoprene, and Styrene

Molecular dynamics simulation of the temperature effect on ideal mechanical properties of SiC/BN interface for SiCf/SiC composites

Molecular dynamics simulation of calcium silicate hydrate/tannic acid interfacial interactions at different temperatures: configuration, structure and dynamic

Molecular Dynamics Simulation of Water Diffusion in Liquid Silicone Rubber

Molecular Dynamics Simulation of Thermal Conductivity of Silicone Rubber

A Molecular Dynamics Simulation on the Relationship Between Contact Angle and Solid-Liquid Interfacial Thermal Resistance