Abstract:The present study involved development of copper-based metal matrix composite, reinforced with waste EN 31 steel chips and TiB 2 ceramic particles. Waste EN 31 steel chips and TiB 2 ceramic particles were ball-milled for 100 h to obtain a single entity. The composite material was produced with a stir-casting technique, followed by a squeeze pressure process. The addition of Cu + 10 wt% of waste steel chips + 5 wt% of TiB 2 improved the tensile strength of the copper matrix by about 68.35%. Furthermore, the addition of Cu + 5 wt% of waste steel chips + 10 wt% of TiB 2 and Cu + 12.5 wt% of waste steel chips + 2.5 wt% of TiB 2 increased the hardness and toughness of the copper matrix by about 133.33% and 28.57%, respectively. The addition of Cu + 10 wt% waste steel chips + 5 wt% of TiB 2 ensured minimal corrosion weight loss in the metal matrix composite as a result of low porosity and a strong bond between the molecules. Further, representative volume element (size: 225 × 225 × 225 nm)-based finite element analysis was done to explain the micro-mechanical deformation, interfacial strength of matrix-particle interaction and damage behavior of Cu + 10 wt% of waste steel chips + 5 wt% of TiB 2 metal matrix composite. A user material sub-routine model was also written and implemented with the help of FORTRAN subroutines to simulate the macro-mechanical tension test process of Cu + 10 wt% waste steel chips + 5 wt%TiB 2 metal matrix composite. The results revealed a good agreement between the micro-mechanical and macro-mechanical finite element analysis models on the one hand and the experimental results on the other. Further, the representative volume element (with matrix and particles) showed about 59% and 66.5% higher tensile strength compared to the matrix–particle interface and the matrix (without particles), respectively. The percentage difference between the micro-mechanical finite element analysis and the experiments as well as the macro-mechanical finite element analysis and the experiments was found to be 5.58% and 9.64%, respectively. The finite element analysis results established that the waste steel chip powder particles exhibited greater stress than the TiB 2 powder particles.

Development and investigation of aluminum metal matrix composite reinforced with copper, nickel, zinc and silicon carbide particle

Performance analysis and mechanical behavior of aluminum metal matrix composite

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Evaluation of Mechanical Properties of Aluminum-Silicon Carbide Metal Matrix Composite

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Experimental Investigation and Comparative Analysis of Aluminium Hybrid Metal Matrix Composites Reinforced with Silicon Nitride, Eggshell and Magnesium

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Investigation on mechanical properties and deformation behavior of copper-based three-phase metal matrix composite: Experimental and micro-macro-mechanical finite element analysis

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Sensitivity Analysis of Reinforced Aluminum Based Metal Matrix Composites

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Mechanical Behaviour of Aluminium Hybrid Composites Reinforced with: Rice Husk Ash - Silicon Carbide - Copper Nanoparticles

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Investigation of Stress and Wear Analysis for Aluminum-based Metal Matrix Composite Reinforced Silicon Carbide using ANSYS Software Package

Microstructural Characterization, Mechanical And Wear Behaviour Of Al2024-B4C Composites For Aerospace Applications

STUDY OF MECHANICAL PROPERTIES AND WEAR BEHAVIOR OF ALUMINUM MATRIX COMPOSITES REINFORCED WITH SILICON CARBIDE PARTICLES

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Study on Metallurgically Prepared Copper-Coated Carbon Fibers Reinforced Aluminum Matrix Composites