Abstract:The paper investigated the effect of selected processing conditions during gear grinding on the value and distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment (TCT) conducted by a continuous single-piece flow method.The gears were carburised with LPC at 920C, then quenched in a 4D Quenching chamber at 7 bar and tempered at 190C for 3 hours. In the next step, the working surfaces of the gear teeth were ground by supplying grinding fluid (GF) to the grinding zone using the WET method and the MQL method with a minimum amount. Measurements were made on the distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment and after the grinding process.The results of the study showed the influence of workpiece speed vw and the method of delivery to the grinding zone GF on selected parameters describing the condition of the technological surface layer of the teeth of gears made of 20MnCr5 steel. The grinding process with a white aluminium oxide grinding wheel causes deterioration in the material's residual stress state. For each of the three analysed workpiece speeds vw, smaller changes in microhardness with respect to the microhardness of the material before grinding occur in the surface layer of samples ground with GF fed with the MQL method. Similarly, residual stress values are in the area of favourable compressive stresses.Environmental considerations and the need to comply with increasingly stringent environmental protection and worker safety regulations are pushing researchers and entrepreneurs to completely eliminate or reduce the consumption of grinding fluids in the grinding process. Based on the research and analysis carried out in this study, it was concluded that applying minimum GF by the MQL method could be an alternative to the conventional WET method.In sustainable manufacturing, it is extremely important to produce high-quality items while reducing the cost of manufacturing and taking care of the environment and workers' health. This includes the manufacture of gears, a basic component used in gear transmissions in the automotive industry, for example. The research has established that it is possible to use the MQL method, which reduces the amount of GF used when grinding the working surfaces of gear teeth, as an alternative to the conventional WET method.The conducted research was the first to determine the most favourable conditions, in terms of the obtained residual stresses and microhardness, for grinding the working surface of gear teeth using the MQL method.

A case study of gear wheel material and heat treatment effect on gearbox strength calculation

Analytical Solution to Bending and Contact Strength of Spiral Bevel Gears in Consideration of Friction

Engineering support for the manufacture of gears of aviation gas turbine engines providing for the instability of the physical and mechanical properties of their materials

Study on Cracks and Process Improvement for Case Hardened Gear Shaft Straightening

Study on surface temperature evaluation method of hardened helical gear with lengthwise sliding velocity

Micro- and Macroscopic Analysis of Fatigue Wear of Gear Wheel Top Layer-An Impact Analysis of Thermochemical Treatment

ANALYSIS OF METHODS FOR CALCULATING SPUR GEAR FOR DEEP CONTACT STRENGTH

Study on the dynamic characteristics of planetary gear transmission mechanism of metal cold rolling mill

The effect of gear-manufacturing quality on the mechanical and thermal responses of a polymer-gear pair

The Effect of Materials on the Efficiency of the Spiroid Gearing

Modeling and Analysis of Deformation for Spiral Bevel Gear in Die Quenching Based on the Hardenability Variation

Frictional Study of a High-Speed Helical Gear Pair Using Computational and Experimental Thermo-Elastic Analyses

The technique for calculating the strength of a globoid worm gear

Material Selection and Processing Techniques: Crucial Factors for Gear Engineering

Durability Investigation of plastic gears

Effect of grinding conditions of gears made of 20MnCr5 steel after single-piece flow heat treatment on the condition of the surface layer of the tooth working surface

Residual stresses in gear form grinding by considering carburizing heat treatment: multi-field coupled numerical simulation and experimental verification

Design of transmission accuracy of the involute cylindrical gear-worm gear system under large temperature difference based on FE method

Study on the Influence of Heat on Deformation and Stress of Planetary Gear Transmission

Finite Element Analysis of Megawatt Wind Turbine Gearbox

The Gear Shaft Numerical Simulation Based on the Elastoplasticity Finite Elements Method