Abstract:The cryogenic propulsion era started with the use of liquid rockets. These rocket engines use propellants in liquid form with reasonably high density, allowing reduced tank size with a high mass ratio. Cryogenic engines are designed for liquid fuels that have to be held in liquid form at cryogenic temperature and gas at normal temperatures. Since propellants are stored at their boiling temperature or subcooled condition, minimal heat infiltration itself causes thermal stratification and self-pressurization. Due to stratification, the state of propellant inside the tank varies, and it is essential to keep the propellant properties in a predefined state for restarting the cryogenic engine after the coast phase. The propellant’s condition at the inlet of the propellant feed system or turbo pump must fall within a narrow range. If the inlet temperature is above the cavitation value, cavitation will likely to happen to result in the probable destruction of the flight vehicle. The present work aims to find an effective method to reduce the stratification phenomenon in a cryogenic storage tank. From previous studies, it is observed that the shape of the inner wall surface of the storage tank plays an essential role in the development of the stratified layer. A CFD model is established to predict the rate of self-pressurization in a liquid hydrogen container. The Volume of Fluid (VOF) method is used to predict the liquid–vapor interface movement, and the Lee phase change model is adopted for evaporation and condensation calculations. A detailed study has been conducted on a cylindrical storage tank with an iso grid and rib structure. The development of the stratified layer in the presence of iso grid and ribs are entirely different. The buoyancy-driven free convection flow over iso grid structure result in velocity and temperature profile that differs significantly from a smooth wall case. The thermal boundary layer was always more significant for iso grid type obstruction, and these obstructions induces streamline deflection and recirculation zones, which enhances heat transfer to bulk liquid. A larger self-pressurization rate is observed for tanks with an iso grid structure. The presence of ribs results in the reduction of upward buoyancy flow near the tank surface, whereas streamline deflection and recirculation zones were also perceptible. As the number of ribs increases, it nullifies the effect of the formation of recirculation zones. Finally, a maximum reduction of 32.89% in the self-pressurization rate is achieved with the incorporation of the rib structure in the tank wall.

Study of the unusable liquid propellant residues evaporation processes parameters in the tanks of the launch vehicle expended stage in microgravity

Method for passivation of propellant residues in orbital stage tank of launch vehicle

Theoretical and Experimental Study for Static Evaporation Rate of a Self-Developed Liquid Hydrogen Storage Tank

CFD SIMULATION OF THE MOVEMENT OF PROPELLANT RESIDUES IN THE TORUS TANK OF A LAUNCH VEHICLE

Parametric optimization and analysis of thermodynamic venting system in liquid hydrogen tank under microgravity

CFD Investigation on Thermodynamic Characteristics in Liquid Hydrogen Tank During Successive Varied-Gravity Conditions

Thermodynamic Performance on the Pressurized Discharge Process from a Cryogenic Fuel Storage Tank

Dynamics of Condensation and Evaporation of Liquid Nitrogen in a Closed Vessel Pressurized with Helium, Nitrogen, and Their Mixture

Thermal stratification and self-pressurization in a cryogenic propellant storage tank considering capillary effect in low-gravity

Asymmetric Heating and Buoyancy Effects on Heat Transfer of Hydrocarbon Fuel in a Horizontal Square Channel at Supercritical Pressures

Profiles of free Surfaces in Revolved Containers Under Microgravity

Feasibility Study on Space Reorientation for Liquid Hydrogen Tanks by Means of Evaporated Exhaust Gas

Thermal Performance of Liquid Hydrogen Tank in Reduced Gravity

Experimental investigation on evaporation characteristics of RP-3 aviation kerosene droplet above the critical temperature under various pressure conditions

Experimental investigation of liquid transport in a vane type tank of satellite with microgravity

Numerical Simulation on Interface Evolution and Pressurization Behaviors in Cryogenic Propellant Tank on Orbit

Pressurization Performance and Temperature Stratification in Cryogenic Final Stage Propellant Tank

Experimental Study on a Liquid Hydrogen Tank for Unmanned Aerial Vehicle Applications

Analysis and Modeling of No-Vent Filling Process for Liquid-Hydrogen Tank in Orbital Conditions

Effect of Roughness Elements on the Evolution of Thermal Stratification in a Cryogenic Propellant Tank

Experimental Study on Evaporation and Ignition Behavior of RP-3 Fuel with Different Leakage Volumes on Hot Surface