Abstract:In recent years, the rapidly growing consumption of fossil fuels negatively affects the environment and public health has attracted much attention. Much effort has been made to find a clean and renewable alternative energy. Bio-oil, produced by flash pyrolysis, is one of the more encouraging products for valorisation of biomass. It has been identified as a promising alternative energy source for fossil fuel owing to its outstanding characteristics such as higher energy density, more suitable for storage and transportation, less capital investment than any other products of biomass. However, the nature of bio-oil contains high acidity, strong corrosiveness, low heating value, thermal instability and chemical complexity, which severely restrict its wide range of applications as a high quality energy. Therefore, it is necessary to upgrade bio-oil. The upgrading techniques include steam reforming, esterification, emulsification, hydrodeoxygenation, catalytic pyrolysis etc. In this paper, catalytic pyrolysis experiments were performed in a fixed bed with inner diameter of 16mm and height of 380mm for bio-oil model compounds (diacetone alcohol, furfural, ethyl acetate and guaiacol) over different characteristics zeolites (HY, HZSM-5, ZSM-5, P/ZSM-5, La/ZSM-5, Ni/ZSM-5) at the condition of T=400℃, WHSV=4 h-1. The catalysts physical properties were investigated by BET (Brunauer-Emmett-Teller surface area) analyse. Water content was detected by using the method of Karl Fischer (870 KF Titrino). The GC-MS was used to analyze the major constituents of the pyrolytic products qualitatively and quantitatively. After the addition of La, the pore size increased from 0.61 nm (ZSM-5) to 0.89 nm (La-ZSM-5). On the contrary, the pore size of P modified ZSM-5 is 0.49 nm which is smaller than that of ZSM-5. The pyrolytic products of the model compounds included organic fraction, water, coke and gas. Compared with ZSM-5,the coke deposition over the La modified ZSM-5 decreased from 2.61% to 1.99% and the organic fraction increased dramatically from 46.10% to 61.51%, which showed the best performance in terms of products distribution among all modified catalyst. The conversions of overall model components and single model component were calculated respectively. The difficulty of the model components pyrolysis is guaiacol>furfural>ethyl acetate>diacetone alcohol. By adding catalysts, the conversion of totally compounds were increased in different degrees, which meaned zeolite promoted the degree of catalytic pyrolysis. HZSM-5 had a best catalytic pyrolysis activity with the highest totally compounds conversion rate of 65.98%. There was a slight decline in the conversion of model compounds contrasted ZSM-5 with La/P/Ni modified ZSM-5. The major components of catalytic pyrolysis were aromatic hydrocarbons, ketones, phenols and so on. It means that a series of decarboxylation and decarbonylation reactions were taken place during the pyrolysis process. On the one hand, the reduction of the oxygen content of bio-oil help to improve its stability, on the other hand it will enhance its heating value. The optimal selectivity of aromatic reached 7.36% over HZSM-5. The La modified ZSM-5 improved the selectivity of aromatic from 6.72%to 7.28%. The highest yield of saturated alcohol was 7.1%over ZSM-5 and decreased using modified ZSM-5. According to the catalytic pyrolysis products distribution, the different reaction pathways for model compounds were discussed, which provided a theoretical basis for experimental study of upgrading bio-oil.

Catalytic co-pyrolysis of seaweeds and cellulose using mixed ZSM-5 and MCM-41 for enhanced crude bio-oil production

[Influence of ZSM-5(38)/Al-MCM-41 Composite Molecular Sieve Catalysts on Pyrolysis of Cellulose].

Catalytic Fast Pyrolysis of Cellulose in a Microreactor System Using Hierarchical Zsm-5 Zeolites Treated with Various Alkalis

Study on the Pyrolysis of Cellulose for Bio-Oil with Mesoporous Molecular Sieve Catalysts.

Preparation of aromatics from fast catalytic pyrolysis of cellulose over alkali-treated HZSM-5

Catalytic co‐pyrolysis of macroalgal components with lignocellulosic biomass for enhanced biofuels and high‐valued chemicals

Catalytic conversion of cellulose over mesoporous Y zeolite

Catalytic pyrolysis of bio-oil model compounds over La/P/Ni modified ZSM-5

Increased aromatics production by co-feeding waste oil sludge to the catalytic pyrolysis of cellulose

In-depth Study of Synergism Between Torrefaction and Catalyst for Balanced Production of Bio-Oil from Rice Husk Pyrolysis Based on Hydrocarbons Production, Energy Yield and Deoxygenation Degree

Study on ZSM-5 Catalytic Pyrolysis Mechanism of Cellulose Based on the Py-GC/MS and the Density Functional Theory

Catalytic Co-Pyrolysis of Cellulose and Polypropylene over All-Silica Mesoporous Catalyst MCM-41 and Al-MCM-41.

Hydrocarbon-Rich Bio-Oil Production from Ex Situ Catalytic Microwave Co-Pyrolysis of Peanut Shells and Low-Density Polyethylene over Zn-Modified Hierarchical Zeolite

Potentiality of combined catalyst for high quality bio-oil production from catalytic pyrolysis of pinewood using an analytical Py-GC/MS and fixed bed reactor

Microwave-assisted catalytic upgrading of co-pyrolysis vapor using HZSM-5 and MCM-41 for bio-oil production: Co-feeding of soapstock and straw in a downdraft reactor

Effect of H-ZSM-5 and Al-MCM-41 Proportions in Catalyst Mixtures on the Composition of Bio-Oil in Ex-Situ Catalytic Pyrolysis of Lignocellulose Biomass

Biomass:polystyrene co-pyrolysis coupled with metal-modified zeolite catalysis for liquid fuel and chemical production

Improving catalytic production of aromatic hydrocarbons with a mesoporous ZSM-5 modified with nanocellulose as a green template

Catalytic Pyrolysis of Microcrystalline Cellulose with Five Molecular Sieve Based Catalysts in Py-GC-MS

Catalytic fast co-pyrolysis of Douglas Fir and low-density polyethylene with nanocellulose-derived carbon catalyst for enhancing selectivity of hydrogen in syngas and mono-aromatic hydrocarbon in bio-oil products

Characterization and mechanism elucidation of high-quality bio-oil production from co-pyrolysis of waste low-rank coal fines and de-oiled microalgae biomass using bimetallic (Cu-Cr) ZSM-5 catalyst