Abstract:This paper looks at the tribology of thermal sprayed WC–Co based coatings and covers the high energy air–sand erosion resistance and slurry jet impingement erosion performance, dry and wet sliding tribology of thermal spray WC–Co based coatings as well as the abrasion and abrasion–corrosion of these coatings. The tribological and tribo-corrosion performance of the coatings will be related to their mechanical and corrosion properties as well as deposition parameters, microstructure and actual composition. For example, the anisotropic microstructure of thermally sprayed WC–Co–Cr coatings, in particular the low fracture toughness in a direction parallel to the substrate, has been observed to affect the nature of crack formation under 200μJ air–solid particle erosion conditions. Voids and occasionally other microstructural features (i.e., cobalt lakes, splat boundaries, interfacial inclusions) in the coating act as crack initiation sites. The erosion rate was dominated by cracks within 5μm of the surface and was relatively insensitive to total length of cracks, showing a near-surface damage front controls the erosion rate and this region is coincident with the region of maximum shear stress induced by erodent impacts. Optimisation of the deposition parameters of HVOF 86WC–10Co–4Cr coatings show an improvement in erosion resistance of more than 50% over the conventional D-gun applied coating of identical nominal composition. The variation in the slurry erosion performance of the thermally sprayed coatings is also linked to directional fracture toughness and crack propagation paths which are influenced by the presence of pores, inhomogeneous carbide distributions and substrate grit blast remnants. The influence of slurry jet angle is more pronounced under 0.4μJ energy conditions where maximum erosion occurred at 90° and the minimum at 30° in contrast to 7μJ slurry erosion rates which were independent of jet angle. This reflects the lower levels of fluctuating stresses imparted to the coating during low energy slurry impacts leading to the impact angle having a greater effect on sub critical crack growth rate than for higher energy conditions.The abrasion resistance of these coatings was found comparable to sintered cermets of the same composition. The synergistic effects between micro and macro abrasion and corrosion for detonation gun (D-gun) sprayed WC–10Co–4Cr coatings are shown to be significant and depend on the environment. The size effect of the abradant relative to the microstructure and splat size is important as well as the propensity for the various phases to passivate to control corrosion levels. Comparisons between exposed and freshly polished coating surfaces in strong NaOH solutions (pH 11) show that significantly lower wear rates were seen for the exposed surface due to a negative wear–corrosion synergy due to selective phase removal and the effects of localised passivation.Dry and wet sliding wear resistance of these coatings is shown to be high (wear rates of 10−16–10−18m3/Nm) with modest coefficient of friction levels between 0.2 and 0.5. The presence of oxides on the binder phases appears to influence the friction and wear levels. Wear appears to be by carbide ejection and/or by tribo-chemical processes.

Erosive Wear Testing of Laser Clad and HVOF Coatings for Drilling in Mining

Wear resistance of a Metco 1030A hard coating deposited on Hadfield steel by laser cladding for ore comminution application

Erosion behaviour of laser cladded Inconel 625 — Vanadium carbide metal matrix composites coatings manufactured with different reinforcement contents

Study on Erosion Behavior of Laser Wire Feeding Cladding High-Manganese Steel Coatings

Resistance of HVOF-Sprayed Cr3C2-25NiCr and WC-10CO-4Cr coatings to cavitation and erosion by mud jetting

Microstructure and Corrosive Wear Properties of CoCrFeNiMn High-Entropy Alloy Coatings

Tribology of thermal sprayed WC–Co coatings

Failure Behavior of Cemented Tungsten Carbide Materials: A Case Study of Mining Drill Bits

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Microstructure and wear resistance of Ni-based tungsten carbide coating by laser cladding on tunnel boring machine cutter ring

Exploration of wear and slurry erosion mechanisms of laser clad CoCrFeNi + x (NbC) high entropy alloys composite coatings

Effect of abrasive particle size and the influence of microstructure on the wear mechanisms in wear-resistant materials

Erosion wear characteristics of cemented carbide for mud pulser rotor

Erosion Behavior of Ti-hBN Multifunctional Coatings in a Custom-made Planetary Test Rig at Extreme Lunar Temperatures

Tribological and dry drilling performance of WS2/Cr-AlCrN coatings

Experimental Study on Water Droplet Erosion Resistance of Coatings (ni60 and WC-17Co) Sprayed by APS and HVOF

The Dry Sliding Wear Behavior of HVOF-Sprayed WC: Metal Composite Coatings

Resistance to Abrasive Wear and Metallurgical Property Assessment of Nine Casing-Friendly Hard-Banding Alloy Chemistries: Abrasion Resistance Assessment Using ASTM G65 Methodology (Standard Test Method for Measuring Abrasion with Dry Sand/Rubber Wheel Apparatus)

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Hydro-abrasive Erosion and Cavitation-Silt Erosion Characteristics of HVOF Sprayed WC-Ni Cermet Coatings under Different Flow Velocities and Sand Concentrations

Corrosion and Wear Behavior of WC–10Co4Cr Coating under Saturated Salt Drilling Fluid