Abstract:Nowadays, pumps of different size are needed for a great variety of purposes. In the past, both computational fluid dynamics (CFD) and experimental flow visualization were performed to reveal flow characteristics within centrifugal pumps, to examine a specific design and to guide design improvement (see Burgreen et al. 1996, 2000). Li et al. (2007) studied the interior viscous flow in a mini pump with an asymmetric axis using CFD and PIV (particle image velocimetry) for improvement of the pump design. Matsui et al. (2002) adopted the the k-ω model in the CFD simulation for a centrfugal pump, and the computational grid system only consisted of one flow passage for LDV (laser Dopler velocimetry) test impeller. Byskov et al. (2003a) and Pedersen & Larsen (2003 b) investigated the flow inside the rotating passages of a six-bladed shrouded centrifugal pump impeller using LES simulation and PIV and LDV measurements. The velocities predicted with LES were in good agreement with the experimental data. The two RANS simulations were, however, not able to predict this complex flow field. It was thus found that using LES for analyzing the flow field in centrifugal pumps could shed light on basic fluid dynamic with a satisfactory accuracy compared to experiments. A transient simulation was used to study the effects of pulsatile blood flow due to the heartbeat through blood pumps by Song et al. (2003). The microsized geometry of the pump made the choice of turbulence models significant for the accuracy of calculation. The comparison showed that the k-ω model gave better predictions of the shear level within the near wall regions than the k-e model. Guleren and Pinarbasi (2004) indicated that the stallcell size extended from one to two diffuser passages. Comparisons of the computational results with experimental data were made and showed good agreement. The unsteady flow in a low specific speed radial diffuser was simulated by the CFD code CFX-10 by Feng et al. (2009). The PIV and LDV measurements had been conducted to validate the CFD results. Both the phase-averaged velocity fields and the turbulence fields obtained from different methods are presented and compared. In this study, in order to get more information about the internal flow of a centrifugal pump, both experimental measurement and numerical simulation are engaged. A centrifugal model pump test rig is built for PIV measurement. The test, involving the technology of index match and fluorescent, is for acquiring flow pattern in a fixed rotational speed, the velocity distribution of the flow field are thus obtained. And, the RANS (Reynolds

Enhancing the Performance of Centrifugal Pump by Adding Cylindrical Disks at Inlet Suction

Computational Fluid Dynamics-Based Pump Redesign to Improve Efficiency and Decrease Unsteady Radial Forces

Cavitation Performance Improvement of High Specific Speed Mixed-Flow Pump

High Efficiency and Low Pressure Fluctuation Redesign of A Centrifugal Pump Based on Unsteady Cfd Analyses

Blade Thickness Redesign to Improve Efficiency and Decrease Unsteady Pressure Pulsation of a Low Specific Speed Centrifugal Pump

Blade Redesign Based on Secondary Flow Suppression to Improve Energy Efficiency of a Centrifugal Pump

Optimization of a Centrifugal Impeller on Blade Thickness Distribution to Reduce Hydro-Induced Vibration

The Optimization of A Low Specific Speed Pipeline Pump

Optimization of a Centrifugal Pump to Improve Hydraulic Efficiency and Reduce Hydro-Induced Vibration

Hydraulic Optimization and Loss Analyses of a Low Specific-Speed Centrifugal Pump with Variable-Thickness Blades

Numerical Simulation of Flow in Centrifugal Pump with Complex Impeller

Numerical Simulation of Inner Flow Field in Centrifugal Impeller with Long, Middle and Short Blades

Numerical Investigation on Cavitation Performance for Centrifugal Pumps with Different Impeller Inlet Geometry

A Performance Test and Internal Flow Field Simulation of a Vortex Pump

Study on the Influence of Centrifugal Pump Inlet Flow Field Instability and Methods of Adjustment

STUDY ON THE REDUCTION OF PRESSURE FLUCTUATION FOR A DOUBLE-SUCTION CENTRIFUGAL PUMP WITH STAGGERED BLADES

Performance Prediction of Centrifugal Pump Based on the Method of Numerical Simulation

Investigation of CFD Calculation Method of a Centrifugal Pump with Unshrouded Impeller

Numerical Simulation on the Steady and Unsteady Internal Flows of a Centrifugal Pump

Improvement Design of a Two-Stage Double-Suction Centrifugal Pump for Wide-Range Efficiency Enhancement

Flow Characteristic Analysis of the Impeller Inlet Diameter in a Double-Suction Pump