Abstract:Ultrashort pulsed laser processing is an effective technology for high-precision cutting, ablation, and drilling of almost all types of material, with low thermal input to the substrate. Polymers which are usually transparent for the laser pulses can be efficiently processed. The material is heated very fast resulting in direct evaporation of the irradiated material volume. On one hand, incubation effects occur due to changed surface roughness, voids, and chemical changes of the material, leading to a variation of energy absorption. On the other hand, if a high repetition rate and high pulse energy are applied to achieve high productivity at polymer cutting, heat accumulation occurs leading to melting and heat affected zones. An estimation of the pulse number dependent material modification and heat input which leads to these effects is not easily accessible for quantitative measurements. Furthermore, numerous process parameters influence the interaction making process analysis and optimization extensive. A versatile tool towards improved knowledge on ultrashort pulsed processes is pump-probe imaging. By using this, effects on a very short timescale such as nonlinear laser absorption, propagation of material waves and plasma generation can be visualized. The recording device in the setup which is applied for the analysis of polymer cutting and drilling in this paper is a high-speed camera with frame rates of up to 50 kHz. This enables recording video sequences contrary to taking a single picture. The authors utilized this to enable the observation of effects of heat accumulation which evolves after a large amount of pulses. Simultaneously, the authors were able to maintain the stated advantages of the pump-probe configuration. Therefore, under variation of several process parameters such as pulse repetition rate, pulse energy, and lateral pulse to pulse separation video sequences were recorded. By a variation of the pump-probe delays of 0 up to 5 ns, material wave propagation can be identified and optimized for evaluation. The points of origin of the observed waves are considered as the regions of highest nonlinear energy deposition; thus, the deposited energy distribution can be estimated. As every single pulse up to a pulse number of 1000 pulses is imaged, the transition from high penetration depth of the first incident pulses to strong surface absorption for an increasing pulse number due to incubation can be shown. Furthermore, strongly absorbing spots in the bulk volume caused by impurities and material modification lead to vapor generation under high pressure. Finally, the confined pressure is assumed to be a main reason for crack formation.

Ultrafast pump-probe ellipsometry and microscopy reveal the surface dynamics of femtosecond laser ablation of aluminium and stainless steel

Physics of picosecond pulse laser ablation

An Atomic-Level Study of Material Ablation and Spallation in Ultrafast Laser Processing of Gold Films

Ultrafast dynamics of hard tissue ablation using femtosecond-lasers

Critical pulse in multi-shot femtosecond laser ablation on metallic surfaces

Case study on the dynamics of ultrafast laser heating and ablation of gold thin films by ultrafast pump-probe reflectometry and ellipsometry

Efficient ablation, further GHz burst polishing, and surface texturing by ultrafast laser

High shock release in ultrafast laser irradiated metals: Scenario for material ejection

The physical mechanisms of short-pulse laser ablation

Influence of Laser-Induced Air Breakdown on Femtosecond Laser Ablation of Aluminum.

Multi-spot ultrafast laser ablation at ambient pressure – A new window on coalescing shock wave interactions

Ultrafast melting, spallation, and phase explosion in femtosecond laser processing on nickel film surface investigated by atomistic simulation and transient reflectivity microscopy

(Sub-)picosecond surface correlations of femtosecond laser excited Al-coated multilayers observed by grazing-incidence x-ray scattering

Measurement of ultrashort laser ablation of four metals (Al, Cu, Ni, W) in single pulse regime

Investigation of ultrashort laser excitation of aluminum and tungsten by reflectivity measurements

Evolution of Microstructures on Stainless Steel induced by Ultra-Short Laser Ablation

Laser-Metal Interaction with a Pulse Shorter than the Ion Period: Ablation Threshold, Electron Emission and Ion Explosion

Transient ablation topography of a thin chromium film after ultrashort pulsed laser irradiation in the spallation and phase explosion regime

Ablation-cooled material removal with ultrafast bursts of pulses

Laser ablation and LIPSS formation at static and dynamic multi-pulse regime on protective Al2O3/TiAlN coating

High-speed pump-probe imaging of ultrashort pulsed laser cutting of polymers