Abstract:Injection of CO2 and water in saline aquifers or oil reservoirs causes changes of pressure, saturation and concentrations that affect the state of stress and promote chemical reactions in the host rock, resulting in porosity and permeability variations. It is therefore a coupled hydro-mechanical and chemical (HMC) problem. Numerical simulation of multiphase and multicomponent flow of CO2, oil and water with mechanical coupling allows realistic modeling of the reservoir and cap rocks. Carbonate reservoirs are geological formations composed mainly of minerals such as calcite and dolomite which can dissolve or precipitate in the medium when injecting a fluid of chemical composition and temperature different from those of the fluids initially contained in the rock. Water-weakening due to matrix acidification of carbonates is a well-known phenomenon that can be modeled by including mineral concentrations as state variables in the stress-strain behavior of the material. The objective of this work is to characterize synthetic carbonate rocks through microtomography and petrography techniques, focusing on a comparative analysis before and after load application and degradation with a reactive fluid [1]. The synthetic rocks were subjected to physical characterization (mineralogy, computed tomography and porosity) and mechanical characterization (uniaxial compressive strength and Brazilian tests) before and after the dissolution process. The petrographic analysis verified an increase in both intergranular and intragranular porosities after dissolution. The microtomography analysis quantified the maximum increase in porosity, from 11.8% to 41.3% in the two-dimensional analysis and 31.6% to 52% in the three-dimensional analysis of the porous structures. Furthermore, the pores were quantified according to their area, and data was obtained on the orientation of the pores, providing insight into the preferred paths of fluid flow. It was also observed that the microtomography technique was an effective tool for characterizing fractures in the samples before and after dissolution [1]. Dissolution tests were also performed in a modified oedometer cell adapted to measure horizontal stress. The dissolution phase was conducted using water and an acid solution to evaluate the influence of the pH on the mechanical behaviour of the samples. When the sample in the oedometric cell is exposed to an acid solution under constant vertical load of 400kPa, vertical displacement takes place (volume decrease of the sample) and horizontal stress increases (Figure 1). The synthetic rock used in this experiment is mainly composed by calcite, with small additions of calcium hydroxide, and the reactive fluid is water acidified with acetic acid (with 10% concentration). This material is manufactured in laboratory in order to have greater control of its constituents and reproducibility of experimental results. During the acidification phase of the experiment, the sample was subjected to an acid flow with a pressure differential of 12kPa for 7h. The behavior in Figure 1 was also observed by [2] and [3]. The model for degradation of carbonatic soft rocks proposed by [2] was implemented in a finite element code capable of performing coupled THMC analyzes in porous media [4]. This model is based on the Critical State Theory with the introduction of a bonding variable that controls the size of the yield surface by modifying the tensile strength and the pre-consolidation stress of the material. In Figure 1 it is also possible to see that the HMC coupled simulation of the oedometric test was able to reproduce the experimental results in terms of volumetric strain and horizontal stress. In Figure 2 tomographic images of the synthetic carbonate rock before and after exposure to the acid solution in an oedometric cell under constant vertical load are presented. Such analyses are crucial for the injection of reactive fluids, such as CO2, at high depths. Dissolution of minerals will affect not only the porosity and permeability of the reservoir rock but also, possibly, the stress state in the vicinity of the injection well.

Impact of Oil Saturation, CO2 Evolution, and Rock Wettability on Acid Efficiencies During Carbonate Acidizing: A Three-Phase Perspective

Effect of Oil Saturation on the Flow of Emulsified Acids in Carbonate Rocks

Pore-scale characterization of carbon dioxide storage at immiscible and near-miscible conditions in altered-wettability reservoir rocks

Pore-Scale Imaging of Controlled-Salinity Waterflooding in a Heterogeneous Carbonate Rock at Reservoir Conditions

Study on the Cleanup Mechanism of Microemulsion Acid Based on Microfluidic Experiment

Improvement of acid solutions for stimulation of compacted high-temperature carbonate collectors

In Situ Pore-Scale Analysis of Oil Recovery During Three-Phase Near-Miscible CO2 Injection in a Water-Wet Carbonate Rock

Reservoir-condition pore-scale imaging of dolomite reaction with supercritical CO 2 acidified brine: Effect of pore-structure on reaction rate using velocity distribution analysis

Mechanistic analysis of matrix-acid treatment of carbonate formations: An experimental core flooding study

Single-Stage Stimulation of Anhydrite-Rich Carbonate Rocks Using Chelating Agent: An Experimental and Modeling Investigation

Numerical investigation of fluid phase momentum transfer in carbonate acidizing

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

Live imaging of micro and macro wettability variations of carbonate oil reservoirs for enhanced oil recovery and CO2 trapping/storage

Experimental Evaluation of CO2-Soluble Nonionic Surfactants for Wettability Alteration to Intermediate CO2-Oil Wet during Immiscible Gas Injection

Numerical analysis of two-phase acidizing in fractured carbonate rocks

Evaluating the Impact of Rock Hardness and Roughness on Acid Fracturing Conductivity

Phase Behavior, Wettability Alteration, and Oil Recovery of Low-Salinity Surfactant Solutions in Carbonate Reservoirs

Supercritical CO2-involved Water–rock Interactions at 85℃ and Partial Pressures of 10–20 MPa: Sequestration and Enhanced Oil Recovery

A comprehensive study on the effect of rock corrosion and CO2 on oil-water interfacial tension during CO2 injection in heavy oil reservoirs

Effect of Oil Chemistry on the Performance of Low Salinity Waterflooding: An Integrated Experimental Approach

Wettability alteration and IFT reduction during carbonated water injection; a critical investigation into the role of pH