Abstract:Empty Fruit Bunches (EFB) are oil palm waste that has the potential as a source of bioenergy because it contains lignocellulose (cellulose, hemicellulose, and lignin) so that it can be converted into biofuel through thermal cracking, adsorption, and distillation processes. Thermal cracking is the decomposition of the chemical content of biomass by utilizing heat without a mixture of oxygen at a temperature of 200oC–600oC. This study aims to obtain the characteristics of the raw material of EFB in the form of proximate, ultimate, lignin, and biofuel produced. The research was conducted using a thermal cracking reactor designed to control the temperature at 300oC, 350oC, 400oC, and 450oC. The results showed that the raw material characteristics of EFB from proximate were 13.66% water content, 8.74% ash content, 58.66% volatile matter and 18.90% fixed carbon. This water content is relatively high. This is because the drying process on the material has not run perfectly. The ultimate result showed that the EFB had a C content of 54.45%, H content of 5.00%, and O content of 16.27%. The atomic ratio obtained from the ultimate analysis can indicate the amount of calorific value that can be used for certain fuels. The smaller the atomic ratio value contained, the more significant the calorific value contained in a particular fuel. Klason method was carried out to decrease the level of lignin through 4 stages; the lignin content without delignification was resulting into 24.87%, the addition of aquadest was resulting into18.71%, the addition of 5% HCl resulting into 15.34%, and 10% HCl resulting into 14.49%. Delignification of 10% HCl is the pretreatment process before the thermal cracking. The thermal cracking process forms steam; the steam is then condensed to obtain bio-oil. The formed bio-oil was kept to separate the oil from tar. In order to obtain good biofuel quality, adsorption is carried out with zeolite adsorbent, which has been activated with HCL. A comparison of the physical properties of bio-oil before and after adsorption shows a color difference from brownish black to the adsorbed bio-oil, which is distilled to separate the heavy and light fractions. The temperature of 450oC at thermal cracking is close to optimum; when the temperature is increased, the cracking process will be more straightforward and occur optimally. The biofuel produced in this study was tested for its characteristics such as, density (927-1086.68 Kg/m3), kinematic viscosity (1.17-1.43 mm2/s), and flash point (66.00-70, 23oC). The biofuel product produced is dominated by C5-C15 compounds (45.07%) according to the results of GC-MS analysis.

Characterization of biomass fuel pellets made from Malaysia tea waste and oil palm empty fruit bunch

Characterization of Empty Fruit Bunch of Palm Oil as Co-firing Biomass Feedstock

Characterizing biomass pellets produced from torrefied biowaste and waste medical plastic pyrolysis oil

Characterization and quality analysis of biomass pellets prepared from furfural residue, sawdust, corn stalk and sewage sludge

Torréfaction to improve biomass pellet made of oil palm empty fruit bunch

Characterization Biofuel from Empty Fruit Bunch through Thermal Cracking

Characterization of binderless fuel pellets from macrophyte Azolla blended with forestry biowaste

Co-fermentation involving Lysinibacillus sp. and Aspergillus flavus for simultaneous palm oil waste treatment and renewable biomass fuel production

Torrefaction and Pelleting of Wheat and Barley Straw for Biofuel and Energy Applications

Torrefaction of Pelletized Oil Palm Empty Fruit Bunches

Co-pyrolysis of plastic waste and eucalyptus waste wood for fuel pellets production: A study of fuel, mechanical, and combustion characteristics under varying binder proportion

Characterization of Biochar Empty Fruit Bunches OPEFB at Various Temperatures and Burning Time

Characterization Studies on Waste Plastics As a Feedstock for Energy Recovery in Malaysia

Hydrothermal Treatment of Empty Fruit Bunch and Its Pyrolysis Characteristics

Development of an efficient method to blend forest biomass with agricultural residue to produce fuel pellets with improved mechanical properties

Thermal Properties of Biochars Derived from Waste Biomass Generated by Agricultural and Forestry Sectors

Pellet production from furfural residue and sawdust: Evaluating the characteristics and quality of pellets and their dependency on process parameters

Characterization of bio-oil and biochar from slow pyrolysis of oil palm plantation and palm oil mill wastes

Utilization of Pine Fruit and Peanut Shell Wastes into Briquettes as an Alternative Fuel

Variability in Physical Properties of Logging and Sawmill Residues for Making Wood Pellets

Pyrolysis of pellets prepared from pure and blended biomass feedstocks: Characterization and analysis of pellets quality