Abstract:Abstract Within the certification process of aircraft, tests under specific icing conditions are required. For such safety relevant tests—which are performed under defined and repeatable test conditions—specially equipped Icing Wind Tunnels (IWT) are required. In such IWTs, supercooled water droplets are created with the aid of a spray system injecting pre-tempered water droplets of specific diameters into the free stream air flow. Especially tests with a droplet size up to 2mm (Supercooled Large Droplets - SLD s) are of great importance. SLDs are difficult to generate under laboratory conditions in IWT since usually the available droplet flight time from the injection location to the impact position on the test object is insufficient to reliably cool down a droplet at least to freezing temperature. To investigate the limitations associated with the application of SLD, the current work provides a method to allow detailed insight into the behavior of droplets on the path from the injection spray nozzle to the test section. In this work a state space model of a single droplet is derived that combines the kinetic aspects, thermal properties as well as the governing differential equations for motion, convective heat transfer at the droplet surface and heat conduction inside the droplet. Beside the states for the droplet’s position and velocity in space, the state space vector comprises various fluid and thermodynamic parameters. The droplet-internal temperature distribution is modelled by a discrete one-dimensional spherical shell model that also incorporates the aggregate phase (freezing mass fraction) at each shell node. This approach allows, therefore, the simulation of potential droplet phase change processes (freezing/melting) as well. With the model at hand, the influence of various boundary conditions (initial droplet temperature, flow field, ambient air temperature, etc.) can be determined and evaluated. As a result, concrete measures to achieve a desired operating condition (e.g. droplet temperature at the test object) for various model assumptions can be derived. In addition, the simulation model facilitates the prediction of the droplet diameter threshold for ensuring a supercooled state upon the impact on the test object. The governing theoretical influences are described, and various simulation results for representative test conditions that occur at the Rail-Tec-Arsenal (RTA) in Vienna are presented.

Comparison of different droplet measurement techniques in the Braunschweig Icing Wind Tunnel

Study on the Method of Droplet Diameter Calibration in Icing Wind Tunnel

Comparison of experimental measuring methods of icing cloud parameters in icing wind tunnel

Kinetic and thermal simulation of water droplets in icing wind tunnels

Particle size distribution measurements under supercooled large drop conditions with Cloud Combination Probe in CARDC icing wind tunnel

Design, construction and commissioning of the Braunschweig Icing Wind Tunnel

Liquid water content measurement with SEA multi-element sensor in CARDC icing wind tunnel: Calibration and performance

Contrast Icing Wind Tunnel Tests between Normal Droplets and Supercooled Large Droplets

Isokinetic Probe Total Water Content Measurements in the NASA Icing Research Tunnel with Supercooled Large Drop Conditions

Effects of Surface Roughness on Splashing Characteristics of Large Droplets with Digital Inline Holographic Imaging

Measurement of Transient Evaporation of an Ethanol Droplet Stream with Phase Rainbow Refractometry and High-Speed Microscopic Shadowgraphy

Simultaneous Measurement of Monocomponent Droplet Temperature/refractive Index, Size and Evaporation Rate with Phase Rainbow Refractometry

Experimental analysis of ice crystal size–velocity correlation in icing wind tunnel with digital holographic particle tracking velocimetry

Research on the Methods for Obtaining Droplet Impingement Characteristics in the Lagrangian Framework

Holographic Airborne for Cloud Particle Imager (HACPI): Development and Applications to Icing Wind Tunnels

A Hybrid Modelling of a Water and Air Injector in a Subsonic Icing Wind Tunnel

Atmospheric icing meteorological parameter study using field experiments and simulation

Calculation and Analysis of Heat and Mass Transfer for Water Droplet in Icing Tunnel Test

Change of Evaporation Rate of Single Monocomponent Droplet with Temperature Using Time-Resolved Phase Rainbow Refractometry

Supercooled large droplet size distribution effects on airfoil icing: A numerical investigation based on a new coupled Eulerian method

Experimental Investigation and Statistical Analysis of Icing Nucleation Characteristics of Sessile Water Droplets