Abstract:Measurement of cumulative dose ƒ(0,150) with a small ionization chamber within standard polymethyl methacrylate (PMMA) CT head and body phantoms, 150 mm in length, is a possible practical method for cone-beam computed tomography (CBCT) dosimetry. This differs from evaluating cumulative dose under scatter equilibrium conditions within an infinitely long phantom ƒ(0,∞), which is proposed by AAPM TG-111 for CBCT dosimetry. The aim of this study was to investigate the feasibility of using ƒ(0,150) to estimate values for ƒ(0,∞) in long head and body phantoms made of PMMA, polyethylene (PE), and water, using beam qualities for tube potentials of 80-140 kV. The study also investigated the possibility of using 150 mm PE phantoms for assessment of ƒ(0,∞) within long PE phantoms, the ICRU/AAPM phantom. The influence of scan parameters, composition, and length of the phantoms was investigated. The capability of ƒ(0,150) to assess ƒ(0,∞) has been defined as the efficiency and assessed in terms of the ratios ε(ƒ(0,150) / ƒ(0,∞)). The efficiencies were calculated using Monte Carlo simulations for an On-Board Imager (OBI) system mounted on a TrueBeam linear accelerator. Head and body scanning protocols with beams of width 40-500 mm were used. Efficiencies ε(PMMA/PMMA) and ε(PE/PE) as a function of beam width exhibited three separate regions. For beam widths < 150 mm, ε(PMMA/PMMA) and ε(PE/PE) values were greater than 90% for the head and body phantoms. The efficiency values then fell rapidly with increasing beam width before levelling off at 74% for ε(PMMA/PMMA) and 69% for ε(PE/PE) for a 500 mm beam width. The quantities ε(PMMA/PE) and ε(PMMA/Water) varied with beam width in a different manner. Values at the centers of the phantoms for narrow beams were lower and increased to a steady state for ~100-150 mm wide beams, before declining with increasing the beam width, whereas values at the peripheries decreased steadily with beam width. Results for ε(PMMA/PMMA) were virtually independent of tube potential, but there was more variation for ε(PMMA/PE) and ε(PMMA/Water). ƒ(0,150) underestimated ƒ(0,∞) for beam widths used for CBCT scans, thus it is necessary to use long phantoms, or apply conversion factors (Cƒs) to measurements with standard PMMA CT phantoms. The efficiency values have been used to derive (Cƒs) to allow evaluation of ƒ(0,∞) from measurements of ƒ(0,150). The (Cƒs) only showed a weak dependence on scan parameters and scanner type, and so may be suitable for general application.

Development of a head CT dose index (CTDI) phantom based on polyester resin and methyl ethyl ketone peroxide (MEKP): a preliminary study

Evaluating polyester resin as a viable substitute for PMMA in computed tomography dosimetry phantoms

Comparing tissue-equivalent properties of polyester and epoxy resins with PMMA material using Gate/Geant4 simulation toolkit

Evaluation of cumulative dose for cone-beam computed tomography (CBCT) scans within phantoms made from different compositions using Monte Carlo simulations

Measurement of computed tomography modulation transfer function with a novel polymethyl methacrylate phantom

SU‐E‐I‐41: Study On the CT Radiation Attenuation Characteristics of Human Body for Phantom Design Using Monte Carlo Simulations

On the gamma radiation response of commercially available 3D printing materials for medical dosimetry

Dosimetric characteristics of 3D-printed and epoxy-based materials for particle therapy phantoms

A direct comparison of multi-energy x-ray and proton CT for imaging and relative stopping power estimation of plastic and ex-vivo phantoms

Assessing suitability and stability of materials for a head and neck anthropomorphic multimodality (MRI/CT) phantoms for radiotherapy

Development of a 3D-printed phantom for total skin electron therapy dose assessment

Estimation of Effective Doses in Head CT Based on RPLGD In-Phantom Measurements

Developing a novel phantom for image quality evaluation in digital radiography

Digital phantom versus patient‐specific radiation dosimetry in adult routine thorax CT examinations

A model for estimating peak skin dose in CT

Dosimetry Evaluation of Treatment Planning Systems in Patient-Specific 3D Printed Anthropomorphic Phantom for Breast Cancer after Mastectomy using a Single-Beam 3D-CRT Technique for Megavoltage Electron Radiation Therapy

Lifelike PixelPrint phantoms for assessing clinical image quality and dose reduction capabilities of a deep learning CT reconstruction algorithm

CT Dosimetry: Comparison of Measurement Techniques and Devices

A New Phantom Developed To Test The Atcm Performance Of Chest Ct Scanners

Radiation dose efficiency of multi-energy photon-counting-detector CT for dual-contrast imaging

Evaluation of Fused Deposition Modeling Materials for 3D-Printed Container of Dosimetric Polymer Gel