Abstract:The requirement of improving efficiency and performance leads to the continuous development of furnaces and burners. For this purpose, it is necessary to establish a model suitable for industrial production and adjust it according to industrial demand. In this paper, a comprehensive numerical model is developed to characterize the combustion, heat transfer, and slab heating in an indirect reheating furnace with pulse combustion. To realize the pulse combustion process, a pulse control approach based on a user-defined function (UDF) was proposed to control the radiant tube burner state. Indirect heat transfer in the furnace was realized by coupling the radiant tubes and the furnace as a whole. In a simulation with the eddy dissipation concept (EDC) model, results from the four-step mechanism were in close accordance with those of the GRI 3.0 mechanism, and both mechanisms could describe the combustion process in detail. However, the calculation time of the EDC model with the four-step mechanism was reduced significantly. Thus, the EDC model with the four-step mechanism was selected as the ideal combustion model used for further simulation research. Through experimental validation, the simulation results of the developed model using the EDC model with the four-step mechanism showed a good agreement with the experimental results. Additionally, with this model, the effects of oxygen-enriched combustion with 74 vol % N<sub>2</sub> and 26 vol % O<sub>2</sub> in the oxidizer and inlet-change case with a fuel inlet and a primary air inlet on the performance of an indirect reheating furnace with pulse combustion were specially studied. The maximum flame temperature and the average temperature of the furnace atmosphere increased from 2046 to 2175 K and from 1241 to 1279 K for increased oxygen concentration, respectively. Compared with air-fuel combustion, the discharging slab temperature reached a growth of 2.9% in oxygen-enriched combustion. After changing the inlet boundary of the radiant tube burners, since the excessive combustion in the burner's combustion chamber was avoided and the full combustion of fuel in the radiant tubes was promoted, the flame intensity in the radiant tubes was enhanced and the maximum flame temperature reached 2196 K. At the same time, the mole fraction of CO at the outlet became smaller and the slab temperature in all zones of the furnace increased by more than 3.5%. This study showed that higher efficiency of an indirect reheating furnace with pulse combustion can be achieved by oxygen-enriched combustion and changing the inlet boundary of the burners.

Modeling and Optimization of Experimentally Verified Effect of Preheated Excess Air on Fuel consumption of Rotary Furnace using PSO (Particle Swarm Optimization) Technique

Consistent Optimization of Blast Furnace Ironmaking Process Based on Controllability Assurance Soft Sensor Modeling.

Effect of Oxygen Enrichment on Flow Field, Temperature, and Gas Concentration Profile Inside a Pilot-Scale Rotary Hearth Furnace

A Study of Optimization Strategy for Furnace Temperature Control System Based on Particle Swarm Optimization (PSO)

Influence of burner nozzle configuration, and inlet gas composition on combustion, gas dynamics, temperature and concentration profile in a rotary hearth furnace

Reduction of Fuel Utilization Through Oxygen-Enriched Combustion in a Reheat Furnace Pusher-Type

Optimizing Pulse Combustion Parameters in Carbon Anode Baking Furnaces for Aluminum Production

Numerical Analysis of the Effects of Oxygen-Enriched and Different Inlet Conditions on Performance of an Indirect Reheating Furnace with Pulse Combustion

Prediction and Optimization of Combustion Performance and Emissions for Lean Methane-Hydrogen Non-Premixed Flame Using RSM-PSO Methodology

Effect of coal powder mass-energy conversion efficiency on oxygen coal ironmaking and parameter optimization

Effect of air supply on combustion and emission characteristics of biodiesel in industrial furnace

Optimization of performance and emission characteristics of liquid fuel fired porous medium burner using RSM and desirability approach

Research on Section Temperature Field Reconstruction in Furnace Based on Hybrid PSO-Powell Algorithm

Optimization of Air Staging in a 1 MW Tangentially Fired Pulverized Coal Furnace

Optimization of Blast Furnace Ironmaking Using Machine Learning and Genetic Algorithms

Modeling the co-combustion of bi-fuel blends in a drop tube furnace: A numerical approach

Optimization of lower air inlet tube configuration for maximizing burner efficiency based on gas dynamics, and heat transfer potency in a Rotary Hearth Furnace

Online Optimization of Cracking Furnace Based on Advanced PSO Algorithm and Neural Network Ensembles

Diesel Engine Performance and Emission Parameters Optimization Using Taguchi and Response Surface Methodology

A Computational Study on the Reduction Behavior of Iron Ore/Carbon Composite Pellets in Both Single and Multi-layer Bed Rotary Hearth Furnace

Cleaning Schedule Optimization of Heat Exchanger Networks Using Particle Swarm Optimization