Abstract:The current research paper presents an investigation of the piezoelectric performances of five different polyvinylidene fluoride hexafluoropropylene (PHP) systems fabricated by electrospinning. Morphological and structural analyses of neat PHP, PHP/zinc oxide 1% (PHP‐Z), PHP/mesoporous silica 1% (PHP‐M), PHP/ZnO‐mesoporous silica at 1 wt.% (PHP‐MZ1), and PHP/ZnO‐mesoporous silica at 3 wt% (PHP‐MZ3) were carried out systematically by scanning electron microscopy, transmission electron microscope, energy‐dispersive X‐ray spectroscopy (EDX), and X‐ray diffraction (XRD). The microscopic analysis results show the formation of uniform ZnO nanoflakes of approximately 5 nm in diameter, whereas mesoporous silica particles form a uniform spherical structure with a typical diameter of 5 μm. Elemental analysis by EDX spectra confirms the presence of Zn, O, and Si in the prepared nanocomposites. The crystalline β‐phase of PHP in the Fourier transformation infrared spectra rises with the addition of ZnO and mesoporous silica particles to the polymer matrix. Neat polyvinylidene fluoride has the most intense XRD peak in comparison to all other polymer nanocomposites. The fabricated flexible nanogenerator obtained from the 1% ZnO‐mesoporous silica nanocomposite shows an output voltage of 2 V, whereas the nanogenerator prepared using the neat PHP sample exhibits an output voltage of ~120 mV. All of the results indicate that the 1% ZnO‐mesoporous silica PHP nanocomposite is suitable for constructing low‐powered wearable self‐driven electrical devices. The article is about the hybrid effect between the mesoporous silica and ZnO and the influence of porosity of nanomaterials. The filler concentration is much lower when compared to the output voltage generated by the electrospun nanofibres. In addition, the present synthesis method stands simple when additional doping procedures (ZnO) are considered. By this research, we aim to fill the gap by studying the combined effect of ZnO and mesoporous silica on the mechanical energy harvesting property of polyvinylidene fluoride hexafluoropropylene.

Development of Al foil-based sandwich-type ZnO piezoelectric nanogenerators

Piezoelectric Nanogenerator Based on a Flexible Carbon-Fiber/zno–znse Bilayer Structure Wire

Enhanced Piezoelectric Performance of the ZnO/AlN Stacked Nanofilm Nanogenerator Grown by Atomic Layer Deposition

A High Power ZnO Thin Film Piezoelectric Generator

A Self-Supported Structure Hybrid Triboelectric/piezoelectric Nanogenerator for Bio-Mechanical Energy Harvesting and Pressure Sensing

Effect of a-Si thin film on the performance of a-Si/ZnO-stacked piezoelectric energy harvesters

Zinc oxide piezoelectric nano-generators for low frequency applications

Enhanced Nanogenerator Performances of 1-D Al-Doped ZnO Nanorod Arrays through Ultrasonic Wave Systems

Towards a Highly Efficient ZnO Based Nanogenerator

Hydrothermal Deposition of a Zinc Oxide Nanorod Array on a Carbon Nanotube Film As a Piezoelectric Generator

Strategies to Enhance ZnO Nanogenerator Performance via Thermal-Annealing and Cryo-Cooling

Controlled synthesis of luminescent ZnS nanosheets with high piezoelectric performance for designing mechanical energy harvesting device

Adjustable ZnO Nanoarrays/pvdf-Hfp Hybrid Piezoelectric Nanogenerators

Enhancing the Output Voltage of Piezoelectric Nanogenerators Based on ZnO Nanowires Grown by Chemical Bath Deposition Using Compensatory Cu Doping

Supersonically Sprayed Pvdf and Zno Nanoflowers with Built-In Nanocuboids for Wearable Piezoelectric Nanogenerators

Tuning ZnO-based piezoelectric nanogenerator efficiency through n-ZnO/p-NiO bulk interfacing

Piezoelectric nanogenerator using p-type ZnO nanowire arrays.

A novel flexible nanogenerator made of ZnO nanoparticles and multiwall carbon nanotube.

High Performance and Direct Current Piezoelectric Nanogenerators Using Lithium‐doped Zinc Oxide Nanosheets

Development of a piezoelectric nanogenerator based on mesoporous silica/zinc oxide hybrid nanocomposite fibres

An Electrostatic Nanogenerator Based On Zno/Zns Core/Shell Electrets With Stabilized Quasi-Permanent Charge