Abstract:Traditional machine learning methods assume that training and testing data must be from the same machine running condition (MRC) and drawn from the same distribution. However, in several real-time industrial applications, this assumption does not hold. The traditional methods work satisfactorily in steady-state conditions but fail in time-varying conditions. In order to utilize time-varying data in variable MRCs, this article proposes a novel low-level knowledge transfer framework using a deep neural network (DNN) model for condition monitoring of machines in variable running conditions. The low-level features have been extracted in time, frequency, and time–frequency domains. These features are extracted from the source data to train the DNN. The trained DNN-based parameters are then transferred to another DNN, which is modified according to the low-level features extracted from the target data. The proposed approach is validated through three case studies on: 1) the air compressor acoustic data set; 2) the Case Western Reserve University bearing data set; and 3) the intelligent maintenance system bearing data set. The prediction accuracy obtained for the above case studies is as high as 100%, 93.07%, and 100%, respectively, with fivefold cross-validation. These real-time results show considerable improvement in the prediction performance using the proposed approach. Note to Practitioners—Condition-based monitoring schemes are widely applicable to rotating machines in various industries since they operate in tough working situations, and consequently, unpredicted failures occur. These unpredicted failures may cause perilous accidents in the industries. CBM systems prevent such failures, which results in the reduction of equipment damage and, hence, increases machinery lifetime. Modern industries are so complex and generating huge -ata, and these data can be collected using sensors, but placing a large number of sensors is difficult and expensive for different but similar kinds of faults in industries. This also increases the cost due to additional sensors and circuits. In this article, the authors have proposed a novel low-level knowledge transfer framework using the deep neural network (DNN)-based method for condition monitoring of machines in variable running conditions. Low-level features have been extracted to reduce the computations of DNN drastically with improved performance. This article also considered additional faults in the target domain, which is more practical in real-time applications. The proposed scheme has been validated with three case studies on acoustic and vibration signatures.

Multiple regression analysis for change detection in multi-sensory monitoring data with application to induction motor speed condition monitoring

Induction Motor Failure Identification Based on Multiscale Acoustic Entropy Feature Selection and Hierarchical Adaptive Neuro-Fuzzy Inference System with Localized Recurrent Input

Condition monitoring of induction motors: A review and an application of an ensemble of hybrid intelligent models

Discrete Sliding-Mode-Based MRAS for Speed-Sensorless Induction Motor Drives in the High-Speed Range

Multi-sensor data fusion for rotating machinery fault detection using improved cyclic spectral covariance matrix and motor current signal analysis

A speed identification method for induction motor based on MRAS

Improving Regenerating Mode Operation of MRAS-Based Induction Motor Speed Estimation Using the Multilayer Technique

A Learning-Based Method for Speed Sensor Fault Diagnosis of Induction Motor Drive Systems

Sensorless Estimation and Convergence Analysis Based on MRAS for PMSM

On-Line Identification of Moment of Inertia for Permanent Magnet Synchronous Motor Based on Model Reference Adaptive System

Intelligent Condition Monitoring Of Rotating Machinery Through Electrostatic Sensing And Signal Analysis

Bearing Fault Diagnosis of Switched Reluctance Motor in Electric Vehicle Powertrain Via Multisensor Data Fusion

Predictive Maintenance Model Based on Anomaly Detection in Induction Motors: A Machine Learning Approach Using Real-Time IoT Data

Real‐time condition monitoring on VSD‐fed induction motors through statistical analysis and synchronous speed observation

Sensorless speed estimation of mains-fed induction motors for condition monitoring using motor relays

Smart Sensor-Based Monitoring Technology for Machinery Fault Detection

Condition-Based Monitoring in Variable Machine Running Conditions Using Low-Level Knowledge Transfer With DNN

A Novel Hybrid Model for the Prediction and Classification of Rolling Bearing Condition

Real-time Condition Monitoring and Fault Detection of Components Based on Machine-Learning Reconstruction Model

A review on MRAS-type speed estimators for reliable and efficient induction motor drives

Fault Diagnosis of Motor Bearings with Multiple Time-Frequency Extraction Method under Variable Speed Conditions