Abstract:The thermo-hydraulic performance of two shell and tube condensers was investigated with an experimental approach. The experiment is conducted in a water cooled centrifugal chiller test rig. The condensers are made of three-dimensional (3-D) and high fin density integral-fmned (2-D) tubes. 2-D and 3-D tubes all have the diameter of 3/4 inch (19mm). The 2-D tube has external fin density of 56fpi (fins per inch), fin height 1.023mm and 48 internal ribs per circle. The 3-D enhanced tube has the external fin density of 45fpi, fin height of 0.981mm and 45 internal ribs per circle. The 3-D tube is widely used in the water cooled chillers. 2-D tube is a newly designed surface with enhanced external fm density. Condensing heat transfer coefficient of R134a outside single horizontal tube is firstly tested at saturate temperature of 40 degrees C. At the internal water velocity of 2.2m/s, the overall heat transfer coefficients of 2-D tube is in the range of 10364.7 to 12420.9W/m(2)K, 4.2% similar to 9.0% higher than 3-D tube. External condensing heat transfer coefficient is 16.3% similar to 25.2% higher than 3-D tube. The condensers are manufactured with these two types of tubes. Both condensers have the same geometric parameters except the tubes and tube bundle space. The length of tube in the condenser is 4000mm. The tube bundles are arranged in a staggered mode. For the integral-fm tube condenser, the longitudinal tube pitch of tube arrays is 23mm in rows and the transverse is 20mm. At the same power input and cooling water inlet temperature of 32 degrees C, the cooling power of 2-D tube condenser are respectively of 1755.4kW and 1769.4kW; 3-D tube condenser is 1727.5kW and 1770.5kW. The pressure drop increased about 11.2% similar to 15.9% for the 2-D tube condenser compared with 3-D tube condenser. Generally, the two condensers have the same heat transfer performance, while the integral-fm tube condenser saves 15% of copper material consumption.

CONDENSOR DESIGN ANALYSIS WITH KAYS AND LONDON SURFACE DIMENSIONS

Design of condenser for unit air-conditioning using R134a

Temperature and Pressure Drop Analysis of Automobile Minichannel Condenser using CFD

Design Method of Fin-and-tube Heat Exchanger with Smaller Diameter Tubes in R290 Air Conditioner

Principle of designing fin-and-tube evaporator with small diameter tubes for air conditioner

Improving the Heat Transfer Rate of Air Conditioning Condenser by Material Optimization

Effect of Compressor-Discharge-Cooler Heat-Exchanger Length Using Condensate Water on the Performance of a Split-Type Air Conditioner Using R32 as Working Fluid

Design of evaporator of R134a unit air-conditioning

Design and Manufacture of Orifice Tube Car Air Conditioning System Simulator with R134a Cooling Fluid

Experimental Study on Heat Transfer Characteristics of A Condenser in the Presence of Air

Thermohydraulic and condensing phase-change analysis within the indoor unit of a split-type air-conditioner

Experimental Study Of Water Cooled Condenser Made Of Three Dimensional And High Fin Density Integral-Finned Tubes

Nominal Condensing Capacity and Performance Evaluation of Evaporative Condenser

Sizing Charts of Helical Capillary Tubes Used in Refrigeration and Air Conditioning

Analysis and investigation of a mobile air conditioner condenser-fan unit

Optimization of a microchannel condenser with separation circuitry

Flow Analysis of Condenser Cooling Air Delivery Via Building Light Well

Development of Small-diameter Tube Heat Exchanger : Circuit Design and Performance Simulation

Investigation of Domestic Air Conditioner with a Novel Low Charge Microchannel Condenser Suitable for Hydrocarbon Refrigerant

Condensation of R134a and R22 in Shell and Tube Condensers Mounted with High-Density Low-Fin Tubes

Simulation Study on Fin-tube Condenser