Abstract:<math>{101¯2}</math> twins were introduced into the magnesium (Mg) plate AZ31 via pre-rolling along its transverse direction. The plates, both with and without the pre-induced <math>{101¯2}</math> twins, were subjected to uniaxial tension along different directions. Using crystal plasticity modeling, we found that the strengthening effect of the pre-induced <math>{101¯2}</math> twins on the macroscopic flow stress primarily arised from the increased slip resistance caused by the boundaries, rather than the orientation hardening due to the twinning reorientation (although the latter did make its contribution in some specific loading directions). Besides, the pre-existing <math>{101¯2}</math> twins were found, by both experiments and simulation, to promote the activity of prismatic 〈a〉 and pyramidal 〈c + a〉 in the parent matrix of the material. Further analysis showed that the enhanced non-basal slip activity is related to the <math>{101¯2}</math> twin boundaries' low micro Hall-Petch slope ratios of non-basal slips to basal slip. With the critical resolved shear stress (CRSS) obtained from crystal plasticity modeling and the orientation data from EBSD, a probability-based slip transfer model was proposed. The model predicts higher slip transfer probabilities and thus lower strain concentration tendencies at <math>{101¯2}</math> twin boundaries than that at grain boundaries, which agrees with the experimental observation that the strain localization was primarily associated with the latter. The present findings are helpful scientifically, in deepening our understanding of how the pre-induced <math>{101¯2}</math> twins affect the strength and slip activity of Mg alloys, and technologically, in guiding the design of the pre-strain protocol of Mg alloys.

Annealing twins in high purity aluminium processed by dynamic equal channel angular pressing

Twinning During Recrystallization and Its Correlation with the Deformation Microstructure

Evolution of Annealing Twins in a Hot Deformed Nickel-Based Superalloy

Annealing Behavior of Aluminium Deformed by Equal Channel Angular Pressing

Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys

EBSP Study of the Annealing Behavior of Aluminum Deformed by Equal Channel Angular Processing

An Atomic-Level Mechanism of Annealing Twinning in Copper Observed by Molecular Dynamics Simulation

Microstructure Evolution in High Purity Aluminum Single Crystal Processed by Equal Channel Angular Pressing (ECAP)

Macro deformation twins in single-crystal aluminum

Annealing twin mechanism for 304 stainless steel solution treatment process

Texture weakening effect from { 10 1 ̅ 1 } twins induced static recrystallization in ambient extrusion AZ31 magnesium alloy

Twin inheritance effect of thermomechanical-processing NiTiCu shape memory alloy

Deformation Twins and Stacking Faults in an AA5182 Al-Mg Alloy Processed by High Pressure Torsion

Introducing transformation twins in titanium alloys: an evolution of α-variants during additive manufacturing

Annealing hardening in cryo-rolled high-entropy alloys by belated deformation twinning

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

Investigation of nanotwins in the bimodal-structured Fe22Co22Ni20Cr22Mn14 alloy subjected to high-strain-rate deformation at cryogenic temperatures

In Situ Study of the Microstructural Evolution of Nickel-Based Superalloys with High Proportional Twin Boundaries Obtained by High-Temperature Annealing

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

Effect of deep cryogenic treatment on martensitic lath refinement and nano-twins formation of low carbon bearing steel

Garnet perspectives on the metamorphic history and tectonic significance of Paleoproterozoic high-pressure mafic granulites from the northern Hengshan, North China Craton