Abstract:The trajectory and adhesion behavior of droplets inair-assisted pesticide spraying in greenhouse are closely related with several factors: the velocity field and pressure field of the airflow, the droplets properties (such as droplet size, initial velocity), the spraying angle, as well as the target parameters (such as shape, size and position). This study explored the conditions that influenced the droplets carried by airflow, with a keen emphasis on whether it could touch, instead of going around, and stay on the target. A CFD (computational fluid dynamics) model was introduced for droplet trajectory simulation in an airflow field, in which droplets were traced by discrete phase particle tracking method. A computation region of 1600, 720 and 1000 mm respectively in streamwise, spanwise and normalwise was established. A target with the dimension of 120 mm × 120 mm × 30 mm was placed 400 mm above ground and 840 mm away from the left boundary of the computational domain. To simplify computational complexity, only half of the computational region (1600 mm × 360 mm × 1000 mm) was computed since the whole region was symmetric on both sides of the sprayer in streamwise. The grid number of the actual computation domain was about 0.36 million. A local mesh encryption method was applied around the target in order to increase the resolution of the simulation. The particle diameters involved in this simulation were 10, 30, 40, 50, 60, 70, 80 and 100μm; and the injection angles were adjusted to 90°, 75°, 60°, 45°, 30° and 15° respectively. A discrete phase boundary condition was set which trapped the droplets on the ground (wall) or the target surfaces. The rest of boundaries for discrete phase were set to boundary condition of droplet escaping. The influences of droplet velocity, droplet size and injection angle on deposition rate were evaluated by the CFD simulation and the experiments proved that: the condition of a droplet touching and adhering on target was that the maximum moving time of droplets inx andy direction should be simultaneously longer than the maximum moving time of droplets inz direction in the region around the target. There was a region below the target where droplets could not reach while spraying, and the length of the region was related to spraying angle. The adhesion behavior of droplets was affected by air velocity and droplet size. When the droplet size was 50μm and spraying angle was 60°, the larger the spraying velocity, the lower the deposition rate. The comparison of the deposition rates from simulations and experiments proves that the experiment data agree well with the data from simulation, so the simulation can be taken as reliable and valid measure in droplet deposition evaluation under greenhouse condition.

Orchard Spray Study: A Prediction Model of Droplet Deposition States on Leaf Surfaces

Modeling and analysis of droplet deposition behavior: From the micro and macro perspectives

Relationship between deposition properties and operating parameters for droplet onto surface in the atomization impinging spray

Computational model of pesticide deposition distribution on canopies for air-assisted spraying

Numerical Simulation of Spray Drift and Deposition from a Crop Spraying Aircraft Using a CFD Approach

Effect of airflow angle on abaxial surface deposition in air-assisted spraying

Effect of Different Spray Factors on Charged Droplet Deposit Using Response Surface Methodology

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Canopy Deposition Characteristics of Different Orchard Pesticide Dose Models

Three-Dimensional Simulation on Drift-reduction of Air-assist Spraying

Evaluation of the Effects of Airflow Distribution Patterns on Deposit Coverage and Spray Penetration in Multi-Unit Air-Assisted Sprayer

Evaluating Effective Swath Width And Droplet Distribution Of Aerial Spraying Systems On M-18b And Thrush 510g Airplanes

Factors Affecting Droplet Loss Behind Canopies with Air-Assisted Sprayers Used for Fruit Trees

Theoretical study on atomizing model for target spray nozzle

Quantitative Analysis of Droplet Size Distribution in Plant Protection Spray Based on Machine Learning Method

Influence of Spray Control Parameters on the Performance of an Air-Blast Sprayer

Influence of the Atmospheric Boundary Layer Stability on Aerial Spraying Studied by Computational Fluid Dynamics

Impaction of spray droplets on leaves: influence of formulation and leaf character on shatter, bounce and adhesion

CFD simulation and validation of trajectory and deposition behavior of droplets around target affected by air flow field in greenhouse

Establishment of fog droplet distribution model and study on canopy deposition uniformity

Droplet deposition of agrochemical spraying: Comparison of results from a random‐walk model and CFD simulations