Abstract:Arising from concerns of continuously deteriorating environmental issues, worldwide efforts are dedicated to developing more sophisticated energy storage techniques to replace traditional nonrenewable sources. Given the significant greenhouse gas emissions that occur coincident with current battery production and operation, the introduction of agricultural waste rice hull ash (RHA), a byproduct of biomass combustion, as a source for battery components could facilitate the actual realization of green and sustainable energy storage. Herein, we focus on using RHA to produce SiC with hard carbon (HC) nanocomposites and their mixtures with graphite as Li + battery anodes. Using a simple method developed in our laboratories to control SiO 2 :HC ratios, the intrinsic nanoscale mixing of SiO 2 and HC in RHA provides a natural starting material for carbothermal reduction producing high purity SiC without the need to add an external carbon source. The optimized SiC/HC nanocomposites contain ≈13 wt. % HC, showing BET surface areas >200 m 2 /g. We previously reported the SiC/HC nanocomposites derived from RHA exhibit charge/discharge capacities 3× of current graphite anodes at > 950 mAh g -1 , accompanied by distinct capacity increases. In particular, SiC can be lithiated to Li 1.1-1.4 SiC without forming Li x Si or Li x C. Investigations of the lithiation/delithiation mechanisms using multiple techniques coupled with modeling suggest a cubic (3C-SiC) to hexagonal phase transition (6H-SiC) after long-term cycling, which may explain the origins of extraordinary capacity increments. Moreover, lithiation/delithiation occur without significant volume changes according to XRD and SEM, suggesting that SiC can compete with metallic Si as an anode material as free volumes equivalent to 3× the charged Si are required. Most recently, inspired by the developed concept of adding graphite to improve the performance of silicon-based anodes, we find adding graphite to SiC/HC nanocomposites results in a 3× improvement in capacity increases on cycling, reaching >950 mAh g -1 after 150 cycles. The proposed interactions within the composites will also be addressed in this presentation. It should be noted most silicon/graphite composite anodes use low Si contents of < 30 wt. % to limit the total electrode volume expansion and ensure contacts and conductivities between components, which restrains the practical energy density improvements from using Si in the anodes. In comparison, mixing only 30 wt. % graphite with SiC/HC in the current work results in specific capacities competitive with Si. Furthermore, Si metal can be synthesized via the carbothermal reduction at ≈1900 °C, while battery-grade graphite used today is produced in an environmentally harmful and expensive multistep method that involves heating to ≈3000 °C. The SiC/HC need only be heated to 1450 °C, with hard carbon forming coincidentally providing positive effects on anode performance. In this aspect, directly using SiC/HC or adding a low amount of graphite to further boosts its performance in an apparently more environmentally friendly route to alternative anodes.

Influence of induction-annealing temperature on the morphology of barley-straw-derived Si@C and SiC@graphite for potential application in Li-ion batteries

Production of graphitic carbons from plant-based SiC/C nanocomposites for Li-ion batteries

Electrochemical Performance Enhancement of Porous Si Lithium-Ion Battery Anode by Integrating with Optimized Carbonaceous Materials

The impact of carbon material microstructure on li-ion storage behaviors of Si in Si/C anodes

Sequencing-Dependent Impact of Carbon Coating on Microstructure Evolution and Electrochemical Performance of Pre-lithiated SiO Anodes: Enhanced Efficiency and Stability via Pre-Coating Strategy

Silicon/Carbon Nanoparticles Assembled with Multifunction Carbon Nanotubes/Sheets as High-Performance Anode of Lithium-Ion Batteries

Optimizing the carbon coating to eliminate electrochemical interface polarization in a high performance silicon anode for use in a lithium-ion battery

Preparation and properties of porous silicon anode coated with nitrogen-doped carbon for lithium-ion battery

Determination of Si/graphite anode composition for new generation Li-ion batteries: a case study

Study of Lithiation Mechanisms of High Performance Carbon-Coated Si Anodes by In-Situ Microscopy

Green Silicon Carbide (SiC) and SiC/Graphite Composite Anodes for Lithium-Ion Batteries

Modulation of Free Carbon Structures in Polysiloxane-Derived Ceramics for Anode Materials in Lithium-Ion Batteries

Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

The preparation of carbon-coated Si nanofiber deposited on carbon nanofiber/natural microcrystalline graphite as the anode for lithium-ion batteries

Latest development of nanostructured Si/C materials for lithium anode studies and applications

Micro-porous carbon coated Si@FeCO 3 nanoflowers for high-performance lithium-ion batteries

Green and facile fabrication of nanoporous silicon@carbon from commercial alloy with high graphitization degree for high-energy lithium-ion batteries

Enhanced reversibility and cyclic stability of biomass-derived silicon/carbon anode material for lithium-ion battery

High-performance silicon-carbon anode material via aerosol spray drying and magnesiothermic reduction

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Building sandwich-like carbon coated Si@CNTs composites as high-performance anode materials for lithium-ion batteries