Abstract:A quantitative evaluation method is used to monitor the extraction effect of four test holes in a field test conducted at Ping Coal Mine 10. The results indicate that, after adopting in situ downhole repair technology in the early stage of extraction, the average air leakage of Borehole No. 4, which failed due to air leakage in the borehole, decreased from 9.33 to 1.26 L/min (a reduction of 86.5%). Similarly, that of Borehole No. 3, which failed due to penetration of fissures in the surrounding rock, had an air leakage drop from 8.35 to 1.34 L/min (a reduction of 84.0%). These improvements demonstrate the remarkable effectiveness of the method. The quantitative evaluation method established in this study is not only simple to operate but also stable and reliable. In this study, a new method is proposed to quantitatively determine the extraction of boreholes under the effect of time. The main purpose of this method is to divide the gas drilling holes in the monitoring time into two stages: the early stage of extraction and the middle stage of extraction. The early stage of extraction uses the gas pressure difference to detect the gas tightness of the drilling holes and determine the type of gas leakage of the drilling holes. Moreover, the unqualified drilling holes are repaired immediately to ensure that all the drilling holes in the middle stage of the monitoring are the qualified holes at the early stage of the inspection. In the middle of extraction, the average attenuation rate of the fitting attenuation curve of pure gas extraction in the extraction borehole is calculated by monitoring, the growth rate of the linear fitting of the pure air leakage is calculated, and their ratios are used as the basis for judging the repair value of the gas leak borehole and the gas leak borehole. This quantitative evaluation method is used to monitor the extraction effect of four test holes in a field test conducted at Ping Coal Mine 10. The results indicate that, after adopting in situ downhole repair technology in the early stage of extraction, the average air leakage of Borehole No. 4, which failed due to air leakage in the borehole, decreased from 9.33 to 1.26 L/min (a reduction of 86.5%). Similarly, that of Borehole No. 3, which failed due to penetration of fissures in the surrounding rock, had an air leakage drop from 8.35 to 1.34 L/min (a reduction of 84.0%). These improvements demonstrate the remarkable effectiveness of the method. The quantitative evaluation method established in this study is not only simple to operate but also stable and reliable. Thus, it is feasible to be applied in the field, which provides important technical support for the improvement in gas extraction effect during coal mine safety production.

Application of short hole rapid extraction technology in excavation face

Study on Gas Drainage Technology of High-level Borehole in Fully Mechanized Caving Face

High efficiency extraction technology and application of bedding directional long borehole along in Coal Roadway

Quantitative evaluation of the sealing effect of penetrating gas drilling and in situ repairing technology for smooth holes

Numerical analysis and control technology of gas accumulation in a large-scale specially-shaped tunnel passing through coal bearing strata

Study on the Application of Comprehensive Gas Control Technology for Source-Separated Three-Dimensional Gas Extraction in Large Mining Faces

Parameter Optimization and Application of Gas Extraction Technology by Buried Pipes in Goaf of Multi-roadway U-type Working Face

Pressure Relief by Blasting Roof Cutting in Close Seam Group Mining under Thick Sandstone to Enhance Gas Extraction for Mining Safety

Improvement of Gas Drainage Efficiency of Low-Permeability Coal Seams Using Ultra-High Pressure Hydraulic Cutting Technique

A novel technology for high-efficiency borehole-enlarging to enhance gas drainage in coal seam by mechanical cutting assisted by waterjet

Study on Borehole Arrangement Methods for Gas Extraction by Hydraulic Slotting in Long-Distance Through-Coal Seam Tunnel

Gas Extraction Mechanism and Effect of Ultra-High-Pressure Hydraulic Slotting Technology: a Case Study in Renlou Coal Mine

Study on Safety Tunneling Technology of Secondary Outburst Elimination by CO2 Gas Fracturing in High-Outburst Coal Seam

Application of integrated drilling and stamping technology in gas extraction through layer drilling

Air Leakage Characteristics of Gas Boreholes in Deep Coal Seams and Application of Short-Hole Grouting and Plugging

Research on controlling gas overrun in a working face based on gob-side entry retaining by utilizing ventilation type “Y”

Numerical simulation and investigation of methane gas distribution and extraction in goaf with U-type ventilation of working face

Key Technology Research on the Rapid-Molding In-Closed Retaining-Wall in Filling Mining

Coal Seam Gas Extraction by Integrated Drillings and Punchings from the Floor Roadway considering Hydraulic-Mechanical Coupling Effect

Study and application of reasonable parameters for hydraulic punching of layer penetration boreholes in Changping Coal Mine