Abstract:Relevance In the Russian Federation, 82 % of oil is produced using Electric Submersible Pumps (ESP), while only 63 % of wells are equipped with such pumps. Since more than half of the operating wells are equipped with ESP, developing methods to reduce operating costs for these wells is a rational and logical allocation of human, material, and financial resources. One method to increase the profitability of oil production from low- and medium-flow rate wells is to transition a well equipped with ESP from continuous operation to intermittent operation, specifically cyclic operation. Intermittent operation reduces energy consumption by up to 40 % and increases oil production by 3 % due to partial gravitational separation of the produced fluid during accumulation. However, the negative effect of transitioning to intermittent operation is reflected in the reduction of the average runtime before failure due to a decreased ESP hydroprotection resource, accelerated wear of the pump unit thrust bearings, and intermediate radial bearings. The cause of these negative effects is the increased vibration level during intensive startup. One way to address these issues is transitioning from the existing scalar open-loop control system to a vector sensorless control system for the ESP. To implement such a system, it is necessary to obtain information about the vector of the ESP state variables. A promising approach to obtaining information about the ESP state involves creating observers based on explicit mathematical models. To create an observer for the state variables, mathematical models for each component of the studied system must be developed and combined into a unified system. When measuring currents and voltages at the output of the step-up transformer, the studied system will be an electric complex «Cable Line — Induction Motor». To implement this observer, it is necessary to determine the parameters of the equivalent circuit of the studied complex. Based on the above, developing a methodology for identifying the parameters of the equivalent circuit of the electric complex «Cable Line — Induction Motor» when measuring currents and voltages on the surface is a timely and relevant task. Solving this task will create prerequisites for the implementation of a vector control system for the ESP, increasing the reliability of the ESP during intermittent operation, and consequently, increasing the profitability of oil production from low- and medium-flow rate oil wells. Aim of research To develop and experimentally confirm the effectiveness of a methodology for assessing the parameters of the electric complex «Cable Line — Induction Motor» based on the balance of consumed power. Research methods Analysis of literary sources, system analysis, mathematical modeling, experimental research. Results The effectiveness of the methodology for assessing the parameters of the electric complex «Cable Line — Induction Motor» based on the balance of consumed power has been experimentally tested and confirmed.

Development of mathematical description of mechanical characteristics of integrated multi-motor electric drive for drying plant

FEA-Based Mathematical Modeling and Simulation for IPMSM Drive with Consideration of Saturation and Cross-Coupling Influence

A novel harmonic elimination approach in three-phase multi-motor drives

Modeling and Realization of Multiphase Permanent Magnet Synchronous Motor Variable Speed System

Issues of Multi-Motor Electric Drive Dynamics through the Example of Converter Tilting Mechanism

Application of ANSYS software package for electromagnetic and thermal analysis of the electric motor of the pilger mill drive seamless pipe manufacturing technology

Preparation Analysis of the Overall Characteristics for High Power PMSM with Multi Phase Units

Method for Defining Parameters of Electromechanical System Model as Part of Digital Twin of Rolling Mill

Torque measurement for researching the energy characteristics of electric vehicle drives

Voltage Stabilisation of a Drive System Including a Power Transformer and Asynchronous and Synchronous Motors of Susceptible Motion Transmission

Modeling vector control of the asynchronous drive of electric rolling stock auxiliary machines

Dynamic Modeling Approach in View of Vector Control and Behavior Analysis of a Multi-Three-Phase Star Permanent Magnet Synchronous Motor Drive

Development and Practical Implementation of Digital Observer for Elastic Torque of Rolling Mill Electromechanical System

DIAGNOSIS OF THE ELECTRIC DRIVE OF THE DISCHARGE ROLLER CONVEYOR OF A WIDE-STRIP HOT MILL

Modeling of the electric drive of the main motion of the rolling cage as a multi-mass electromechanical system

Elaboration of a method of electromechanical drive systems status estimation (at an example of a roll-table roller) by application statistical analysis of electric motor current signal

Development of the energy-efficient asynchronous electric drive of a locomotive blower motor

Development of method to design end-face synchronous motors made of amorphous steel using digital twin technology

Steady-State Modeling of Series-Connected Five-Phase and Six-Phase Two-Motor Drives

METHODOLOGY FOR EVALUATING PARAMETERS OF THE ELECTRICAL COMPLEX «CABLE LINE — INDUCTION MOTOR» BASED ON POWER CONSUMPTION BALANCE

Sensorless torque and power measurement in DC electric drive