Abstract:Fused filament fabrication (FFF) is a cost-effective additive manufacturing method that makes use of thermoplastics to produce customised products. However, there are several limitations associated with FFF that are adversely affecting its growth including variety of materials, rough surface finish and poor mechanical properties. This has resulted in the development of metal-infused thermoplastics that can provide better properties. Furthermore, FFF-printed parts can be subjected to post-processes to improve their surface finish and mechanical properties. This work takes into consideration two commonly used polymeric materials, i.e., ABS (acrylonitrile butadiene styrene) and PLA (polylactic acid) and compares the results with two metal-infused thermoplastics i.e., copper-enhanced PLA and aluminium-enhanced ASA (acrylonitrile styrene acrylate). The four different materials were subjected to a post-process called annealing to enhance their mechanical properties. The effect of annealing on these four materials was investigated through dimensional analysis, ultrasonic testing, tensile testing, microstructural analysis and hardness testing. The results showed that annealing affects the materials differently. However, a correlation among ultrasonic testing, tensile testing and microstructural analysis was observed for all the materials based on their crystallinity. It was found that the semi-crystalline materials (i.e., PLA and copper enhanced PLA) showed a considerable increase in tensile strength post-annealing. However, the amorphous materials (ABS and aluminium-enhanced ASA) showed a comparatively lower increase in tensile strength, demonstrating that they were less receptive to annealing. These results were supported by higher transmission times and a high percentage of voids in the amorphous materials. The highest hardness values were observed for the ASA material and the lowest for the ABS material. This work provides a good comparison for the metal-infused thermoplastics and their applicability with the commonly used PLA and ABS materials.

Hybrid fused filament fabrication for manufacturing of Al microfilm reinforced PLA structures

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Optimization of Process Parameters of Fused Filament Fabrication of Polylactic Acid Composites Reinforced by Aluminum Using Taguchi Approach

Maximizing performance and efficiency in 3D printing of polylactic acid biomaterials: Unveiling of microstructural morphology, and implications of process parameters and modeling of the mechanical strength, surface roughness, print time, and print energy for fused filament fabricated (FFF) bioparts

Mechanical characteristics and failure morphology of FFF-printed poly lactic acid composites reinforced with carbon fibre, graphene and MWCNTs

Short carbon fiber-reinforced PLA composites: influence of 3D-printing parameters on the mechanical and structural properties

Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality

Mechanical Characteristics of Thermoplastic Polymers for 3d Printed Hybrid Structures

Investigation of Fused Filament Fabrication-Based Manufacturing of ABS-Al Composite Structures: Prediction by Machine Learning and Optimization

An experimental analysis of mechanical properties for a dissimilar pattern structure in the 3-D printing of a PLA5F filament using the Taguchi method

Correlation between Infill Percentages, Layer Width, and Mechanical Properties in Fused Deposition Modelling of Poly-Lactic Acid 3D Printing

Hybrid additive manufacturing of highly sustainable Polylactic acid -Carbon Fiber-Polylactic acid sandwiched composite structures: Optimization and machine learning

Investigating the Effects of Annealing on the Mechanical Properties of FFF-Printed Thermoplastics

On the optimized fused filament fabrication of polylactic acid using multiresponse central composite design and desirability function algorithm

Investigation of Fused Deposition Modelling Process Parameters in 3D Printing for Composite Material (Poly Lactic Acid and Banana Fibre)

Numerical Calculation and Properties Study on Polylactic Acid (Pla)/nano-Hydroxyapatite (N-Ha) Composite Fluid 3D Printed by Fused Deposition Modeling

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

Fundamental study and modification of Kenaf fiber reinforced polylactic acid bio-composite for 3D printing filaments

Architecture of covalent bonds between filament layers to enhance performance of 3D printing biodegradable polymer blends

A Surface Modification of Polylactic Acid Composites for Additive Manufacturing with Modified Chopped Carbon Fiber and Modified Nano‐hydroxyapatite

A comprehensive review on fused deposition modelling of polylactic acid