Abstract:The accuracy of 3D reconstructions of the craniomaxillofacial region using cone beam computed tomography (CBCT) is important for the morphological evaluation of specific anatomical structures. Moreover, an accurate segmentation process is fundamental for the physical reconstruction of the anatomy (3D printing) when a preliminary simulation of the therapy is required. In this regard, the objective of this study is to evaluate the accuracy of four different types of software for the semiautomatic segmentation of the mandibular jaw compared to manual segmentation, used as a gold standard. Twenty cone beam computed tomography (CBCT) with a manual approach (Mimics) and a semi-automatic approach (Invesalius, ITK-Snap, Dolphin 3D, Slicer 3D) were selected for the segmentation of the mandible in the present study. The accuracy of semi-automatic segmentation was evaluated: (1) by comparing the mandibular volumes obtained with semi-automatic 3D rendering and manual segmentation and (2) by deviation analysis between the two mandibular models. An analysis of variance (ANOVA) was used to evaluate differences in mandibular volumetric recordings and for a deviation analysis among the different software types used. Linear regression was also performed between manual and semi-automatic methods. No significant differences were found in the total volumes among the obtained 3D mandibular models (Mimics = 40.85 cm3, ITK-Snap = 40.81 cm3, Invesalius = 40.04 cm3, Dolphin 3D = 42.03 cm3, Slicer 3D = 40.58 cm3). High correlations were found between the semi-automatic segmentation and manual segmentation approach, with R coefficients ranging from 0,960 to 0,992. According to the deviation analysis, the mandibular models obtained with ITK-Snap showed the highest matching percentage (Tolerance A = 88.44%, Tolerance B = 97.30%), while those obtained with Dolphin 3D showed the lowest matching percentage (Tolerance A = 60.01%, Tolerance B = 87.76%) (p < 0.05). Colour-coded maps showed that the area of greatest mismatch between semi-automatic and manual segmentation was the condylar region and the region proximate to the dental roots. Despite the fact that the semi-automatic segmentation of the mandible showed, in general, high reliability and high correlation with the manual segmentation, caution should be taken when evaluating the morphological and dimensional characteristics of the condyles either on CBCT-derived digital models or physical models (3D printing).

Pitfalls of Computed Tomography 3D Reconstruction Models in Cranial Nonmetric Analysis*

Photogrammetry vs CT Scan: Evaluation of Accuracy of a Low-Cost Three-Dimensional Acquisition Method for Forensic Facial Approximation

What we see is what we touch? Sex estimation on the skull in virtual anthropology

Quantitative Analysis of Craniofacial Skeleton Asymmetry by Three-Dimensional Computed Tomography

One Step before 3D Printing—Evaluation of Imaging Software Accuracy for 3-Dimensional Analysis of the Mandible: A Comparative Study Using a Surface-to-Surface Matching Technique

Precision Validation of 3-D Reconstruction of the Craniofacial Hard Tissues Based on 2-D Digital Radiograph

Does the choice of the reference model affect the results of 3D-3D superimposition procedure? A comparison of different protocols for personal identification

Virtual anthropology? Reliability of three-dimensional photogrammetry as a forensic anthropology measurement and documentation technique

Three-Dimensional Anthropometric Facial Analysis and Fitting Discrepancies Between Stereophotogrammetry and CT

A comparative study of cranial, blunt trauma fractures as seen at medicolegal autopsy and by computed tomography

3D printing and CBCT anatomical reproducibility assessment in forensic scenarios

Comparison of Craniofacial Anthropometric Measurement Accuracy of Manual Technique vs. Cone-Beam CT Scanning

Model of 3D cephalometric analysis based on three-dimensional computed tomography

Exploring CT pixel and voxel size effect on anatomic modeling in mandibular reconstruction

Assessment of Anatomical Uniqueness of Maxillary Sinuses through 3D-3D Superimposition: An Additional Help to Personal Identification

Statistical and Individual Characteristics-Based Reconstruction for Craniomaxillofacial Surgery

Accuracy assessment of image-based surface meshing for volumetric computed tomography images in the craniofacial region

Human identification: an investigation of 3D models of paranasal sinuses to establish a biological profile on a modern UK population

An exclusionary screening method based on 3D morphometric features to sort commingled atlases and axes

Applications of forensic anthropology methodology: accuracy of virtual face reproductions performed on the Tenchini collection

Comparative Study of Computerized Tomography Imaging of Facial Trauma Using 2D and 3D Reconstruction Scans