Abstract:The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool's exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Studies on the Influence of Stirrer Blade Design on the Microstructure and Mechanical Properties of a Novel Aluminum Metal Matrix Composite

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

A Comparative Study of the Impact of the Stirrer Design in the Stir Casting Route to Produce Metal Matrix Composites

Optimization of process variables and characterization of mechanically agitated ceramic‐microsphere reinforced aluminium composite

Performance analysis and mechanical behavior of aluminum metal matrix composite

Processing and Characterization of AA2618/Sicp Metal Matrix Composites by Stir Casting Method

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

Investigation of graphene nanoplatelets-deposited textured metal matrix composite plates for improved mechanical properties: a numerical approach

Investigate the mechanical properties of Aluminium Metal Matrix Composite

To study the effect of different reinforcements on various parameters in aluminium matrix composite during CNC turning

Impact of Hard and Soft Reinforcements on the Microstructure, Mechanical, and Physical Properties of the Surface Composite Matrix Manufactured by Friction Stir Processing

Fabrication and Mechanical Behaviour Investigation on Aluminium 7075 Boron Carbide and Inconel Alloy 625 Metal Matrix Composite Using Ultra Sonic Stir Casting Method

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Evaluation of Mechanical Properties of Aluminum-Silicon Carbide Metal Matrix Composite

Effect of nano-Sized Al2O3 Particles on Microstructure and Mechanical Properties of Aluminum Matrix Composite Fabricated by Multipass FSW

Influence of Tool Pin Profiles on Aluminium Alloy A356 and Ceramic-Based Nanocomposites for Light Weight Structures by Friction Stir Processing

Influence of Vanadium and Niobium Carbide Particles on the Mechanical, Microstructural, and Physical Properties of AA6061 Aluminum-Based Mono- and Hybrid Composite Using FSP

Optimization of Mixing Parameters for a Cold Model System by CFD for Aluminum Matrix Composites Synthesis Process

Effect of tool diameter ratio on the microstructural characteristics of a solid-state processed aluminum based metal matrix composite