Molecular dynamics simulation and experimental study of micro‐structure and gel properties of single chain alkyl ammonium intercalated Na‐montmorillonite

Jun Qiu,Guowei Chen,Xijiao Cao,Kaibo Cui,Wei Yang,Zhengqing Yan,Yueting Wang,Peng Wu

DOI: https://doi.org/10.1002/app.52310

IF: 3

2022-03-09

Journal of Applied Polymer Science

Abstract:Journal of Applied Polymer Science, EarlyView.

polymer science

What problem does this paper attempt to address?

A Molecular Dynamics Study on the Structural and Mechanical Properties of Pyrophyllite and M-Montmorillonites (M = Na, K, Ca, and Ba)

Zongfang Han,Hua Yang,Mohua Bu,Manchao He

DOI: https://doi.org/10.1016/j.cplett.2022.139848

IF: 2.719

2022-01-01

Chemical Physics Letters

Abstract:In this work, molecular dynamics simulations were performed to reveal the effects of interlayer cations (Na+, K+, Ca2+, Ba2+) on the structural and mechanical properties of montmorillonites (MMTs) and the obtained results were compared with those of pyrophyllite without isomorphous substitutions. Lattice parameters, interlayer spacing and equilibrium volumes were calculated. Based on the stress-strain curve obtained by uniaxial compression, ultimate stress and strain, Poisson's ratio and Young's modulus along three crystal directions were calculated. The obtained results revealed that the mechanical properties of pyrophyllite and MMTs were obviously different and the type of interlayer cations significantly affected the mechanical properties of MMTs, especially along OC direction. The negative correlation between ultimate strain and charge/ionic radius ratio well explains the particularity of the stress-strain curves of K-MMT and Ba-MMT. Moreover, distribution of counterions between layers and their interactions with clay sheets were analyzed and radial distribution function and number density profiles perpendicular to clay surface were calculated.
Microstructure of Different Chain Length Ionic Liquids Intercalated into Montmorillonite: A Molecular Dynamics Study

Limei Wu,Chengxue Yang,Lefu Mei,Faxiang Qin,Libing Liao,Guocheng Lv

DOI: https://doi.org/10.1016/j.clay.2014.07.004

IF: 5.907

2014-01-01

Applied Clay Science

Abstract:This study employs molecular dynamics modeling to examine the interlayer microstructures of montmorillonite intercalated with different chains of CnmimCl montmorillonites with varying chain lengths, intercalation amount, arrangement and energy. C4mim+ and C8mim+ arrange themselves in monolayers, while C12mim+ and C16mim+ in parallel bilayers or tilt aligning. The basal spacing of montmorillonite and the corresponding energy increased as the chain length of organic cations is increased. It is indicated that no bond has been formed for N+O due to the minimum distances of no less than 3.1Å and angles of 35°–45° between N+ in Cnmim+ and silicon–oxygen tetrahedron. These modeling results provide insights into the understanding of synthesized Cnmim+-montmorillonite microstructure and guidelines for relevant engineering applications.
Microstructure and Process of Intercalation of Imidazolium Ionic Liquids into Montmorillonite

Limei Wu,Libing Liao,Guocheng Lv,Faxiang Qin,Zhaohui Li

DOI: https://doi.org/10.1016/j.cej.2013.09.063

IF: 15.1

2014-01-01

Chemical Engineering Journal

Abstract:Organically modified clays exhibit adsorption capacities for cations, anions, and nonpolar organic compounds, which make them valuable for various environmental technical applications. Research into organic molecule modified montmorillonite should place importance on studying the mechanism of the intercalation process. Herein a new kind of green and steady ionic liquid, 1-Hexadecyl-3-methylimidazolium chloride monohydrate (C16mimCl) has been chosen as the intercalant agent. We have investigated the process that C16mimCl is intercalated into Na-montmorillonite in aqueous solution under batch studies and molecular simulations. The C16mimCl intercalation has been found relatively fast with a large rate constant. The intercalation is driven by both cations exchange and negative charge on the layer surface. The process is affected by the initial concentration and pH value of the solution; the basal spacing is increased to 2.88nm after intercalation. Molecular dynamic simulation further reveals that the initial concentration of C16mimCl can influence its configuration in the interlayer, causing the change of interlayer spacing. Apart from the electrostatic interaction, the hydrophobicity of the organic molecule also plays an important role in the intercalation process. Overall, ionic liquid intercalated montmorillonite is a promising environmental composite material with broad application potentials such as chemical fiber and aviation.
Molecular dynamics simulation of dodecyl dimethyl benzyl ammonium cation-intercalated montmorillonite

Haotian Su,Yingchun Zhang,Jinhong Zhou,Qingfeng Hou

DOI: https://doi.org/10.1180/clm.2023.38

2024-02-17

Clay Minerals

Abstract:Dodecyl dimethyl benzyl ammonium (DDBA) is a novel cation surfactant used to modify clay minerals. DDBA-intercalated montmorillonite is formed by the ion exchange between DDBA cations in the solution and cations in the montmorillonite interlayers. By using molecular dynamics simulations, we investigated the basal spacings, interlayer structures and dynamics of DDBA-montmorillonites. The results showed that the calculated basal spacings agreed well with experimental values and that the layering behaviours of DDBA had been revealed. The ammonium groups of DDBA ions preferred staying close to the centre of Si–O six-member rings. The benzyl group and lauryl group were oriented in parallel in the monolayer state, whereas they were tilted in other states. DDBA ions have very low mobility in the interlayer region, indicating that the negatively charged montmorillonite surfaces can effectively fix this positively charged surfactant. The microscopic structures and dynamics obtained in the present study provide atomic-scale insights into the properties of DDBA-intercalated clay minerals.

geosciences, multidisciplinary,mineralogy,chemistry, physical
Molecular Dynamics Simulation of Alkylammonium-Intercalated Vermiculites

Cheng Chen,Xiandong Liu,Yingchun Zhang,Chi Zhang,Xiancai Lu

DOI: https://doi.org/10.1346/CCMN.2017.064070

2017-01-01

Clays and Clay Minerals

Abstract:In order to understand the microscopic properties of alkylammonium-intercalated vermiculites, molecular dynamics simulations employing the clayff-CVFF force field were performed to obtain the interlayer structures and dynamics. The layering behavior of alkyl chains was uncovered. With the model used in the present study (1.2 e per unit cell), the alkyl chains formed monolayers with carbon-chain lengths of C 6 , bilayers from C 7 to C 10 , and pseudo-trimolecular layers from C 15 to C 18 . Intermediate states also existed between bilayer and pseudo-trimolecular layer states from C 11 to C 14 . The ammonium groups had two locations: most ammonium groups were located over the six-member rings (~90%), and the rest above the substitution sites (~10%). The ammonium groups interacted with the vermiculite surface through H bonds between ammonium H atoms and surface O atoms. The ammonium groups were fixed firmly on surfaces and, therefore, had very low mobility. The alkyl chains were slightly more mobile. The similarities and differences between alkylammonium-intercalated vermiculites and smectites were revealed. The layering behaviors of alkyl chains were similar in alkylammonium-intercalated vermiculites and smectites: the alkyl chain behavior was controlled by both the amount of layer charge and the carbon chain length. The distributions of ammonium groups, however, were different, caused by the layer-charge distribution in vermiculites being different from that in smectites. The atomic-level results derived in the present study will be useful for future research into and the applications of organo-vermiculites.
Interlayer structure and dynamics of alkylammonium-intercalated smectites with and without water: A molecular dynamics study

Xiandong Liu,Xiancai Lu,Rucheng Wang,Huiqun Zhou,Shijin Xu

DOI: https://doi.org/10.1346/CCMN.2007.0550602

2007-01-01

Clays and Clay Minerals

Abstract:The structure and dynamics of alkylammonium-intercalated smectites were simulated using molecular dynamics employing the clayff-CVFF force field, the reliability of which was firstly validated for these systems. The layering behaviors of alkyl chains confirm the scenarios of the monolayer, transition and bilayer configurations for short, medium-length and long carbon tails, respectively. In the systems without water, the alkylammonium groups are all anchored firmly above the surface six-member rings through H bonds between ammonium hydrogen and surface oxygen, and the alkyl tails are a little more mobile. With water involved, some ammoniums are dragged out of the potential barriers of the six-member rings by water molecules through the strong H bonds between water oxygen and ammonium hydrogen. The intercalated water scarcely affects the basal spacing, alkyl chain layering or alkylammonium dynamics. It is also found that the systems with alkyl chains of 11 to 14 exhibit the greatest density, resulting in the extremely limited mobility of the intercalated species.
Molecular dynamics simulation of the initial stage induction of alkali-activated aluminosilicate minerals

Feng Guo,Jizhou Chen,Qingyin Tang,Mengqi Sun,Haibao Feng,Hailiang Gao,Mengmeng Li,Shuang Lu

DOI: https://doi.org/10.1039/d4ra00822g

IF: 4.036

2024-01-01

RSC Advances

Abstract:Molecular dynamics simulations were used to study the micro-reaction behavior of geopolymers and to explore the induction process and structural evolution of the initial stages.

chemistry, multidisciplinary
Molecular Dynamics Study of Crystalline Swelling of Montmorillonite as Affected by Interlayer Cation Hydration

Hongliang Li,Shaoxian Song,Xianshu Dong,Fanfei Min,Yunliang Zhao,Chenliang Peng,Yuri Nahmad

DOI: https://doi.org/10.1007/s11837-017-2666-2

2017-11-21

JOM

Abstract:Swelling of montmorillonite (Mt) is an important factor for many industrial applications. In this study, crystalline swelling of alkali-metal- and alkaline-earth-metal-Mt has been studied through energy optimization and molecular dynamics simulations using the clay force field by Materials Studio 8.0. The delamination and exfoliation of Mt are primarily realized by crystalline swelling caused by the enhanced interlayer cation hydration. The initial position of the interlayer cations and water molecules is the dominated factor for the accuracy of the Mt simulations. Crystalline swelling can be carried out in alkali-metal-Mt and Mg-Mt but with difficulty in Ca-Mt, Sr-Mt and Ba-Mt. The crystalline swelling capacity values are in the order Na-Mt > K-Mt > Cs-Mt > Mg-Mt. This order of crystalline swelling of Mt in the same group can be attributed to the differences between the interlayer cation hydration strengths. In addition, the differences in the crystalline swelling between the alkali-metal-Mt and alkaline-earth-metal-Mt can be primarily attributed to the valence of the interlayer cations.

materials science, multidisciplinary,metallurgy & metallurgical engineering,mining & mineral processing,mineralogy
Influence of inorganic and organic salts on the hydration mechanism of montmorillonite based on molecular simulation

Lianjun Yang,Bo Xiang,Haisong Zhao,Kai Wu,Enlong Liu,Ge Zhang

DOI: https://doi.org/10.1038/s41598-023-36137-w

IF: 4.6

2023-06-05

Scientific Reports

Abstract:Abstract The molecular dynamics method is used to further reveal, from the molecular point of view, the mechanisms of salt inhibiting the hydration of Na-MMT. The interaction between water molecules, salt molecules, and montmorillonite are calculated by establishing the adsorption models. According to the simulation results, the adsorption conformation, interlayer concentration distribution, self-diffusion coefficient, ion hydration parameters, and other data are compared and analyzed. The simulation results show that the volume and basal spacing increase in a stepwise manner with the increase of water content, and water molecules have different hydration mechanisms. The addition of salt will enhance the hydration properties of compensating cations of montmorillonite and affect the mobility of particles. The addition of inorganic salts mainly reduces the adsorption tightness between water molecules and crystal surfaces, thereby reducing the thickness of water molecules layer, while the organic salts can better inhibit migration by controlling interlayer water molecules. The results of molecular dynamics simulations reveal the microscopic distribution of particles and the influence mechanism when the swelling properties of montmorillonite are modified by chemical reagents.

multidisciplinary sciences
Molecular dynamics study of the effect of inorganic salts on the monolayer of four surfactants at the oil/water interface

Peng Shi,Hui Zhang,Lin Lin,Chunhui Song,Qingguo Chen,Zesheng Li

DOI: https://doi.org/10.1080/01932691.2018.1462200

2018-08-29

Journal of Dispersion Science and Technology

Abstract:The molecular dynamics (MD) simulation method was used to simulate the aggregation of four types of surfactants at the oil/water interface. The effect of different cations such as Na+, Mg2+ and Ca2+ was compared. The results show that the interaction between different types and concentrations of cationic and head group of surfactants causes the surfactant adsorption layer to bend and changes the aggregation morphology of the micelles. The radial distribution function (RDF) of the surfactant head groups with water molecules and cations is calculated. The calculated results show that it exists a chemical hydration layer and a physical hydration layer between the surfactant head groups and the water molecules. Cation has different degrees of impact, thus changes the original hydration structure. Nonionic and zwitterion surfactants have good salt resistance. Potential of Mean Force (PMF) was used to analyze the energy change when the cation interacted with the polar head. The nonionic and zwitterion surfactants are determined to have a good oil displacement effect even under the conditions of high calcium-magnesium mineralization. The present results could help in choosing surfactants used in oil/water with inorganic salts.

chemistry, physical
Interlayer structure and dynamic properties of CTMAB–montmorillonite: experiment and molecular dynamics

Wei Yang,Xiaohui Xia,Xueying Liu,Shaoqiu Zhang

DOI: https://doi.org/10.1039/d3ra01834b

IF: 4.036

2023-01-01

RSC Advances

Abstract:The intercalation of cetyltrimethylammonium bromide (CTMAB) into montmorillonite will cause interlayer expansion and surface charge reversal.

chemistry, multidisciplinary
Molecular Dynamics Insight into the Cointercalation of Hexadecyltrimethyl-Ammonium and Acetate Ions into Smectites

Xiandong Liu,Xiancai Lu,Rucheng Wang,Huiqun Zhou,Shijin Xu

DOI: https://doi.org/10.2138/am.2009.2887

2009-01-01

Abstract:Classical molecular dynamic simulations are performed to investigate the microscopic properties of hexadecyltrimethylammonium (HDTMA) intercalated smectites with and without the cointercalation of acetate groups. Three model smectites with distinct layer-charge characteristics are selected as the frameworks and their HDTMA intercalates correspond to the representative monolayer, bilayer, and paraffin configurations of the aliphatic chains. In the organoclays without cointercalation, all trimethylammonium headgroups of HDTMA are fixed firmly above the center of the surface six-member rings through electrostatic attractions with surface oxygen, whereas the alkyl chains are a little more mobile. It is found that the cointercalations can significantly increase the basal spacings of the pure HDTMA intercalated smectites. The distributions and mobility of the HDTMA headgroups are not affected by the acetate ions because of the overwhelming attractions coming front the clay sheets. The acetate groups are fixed by the HDTMA headgroups through ion pairing. This simulation study provides a molecular level basis to understand the effects of cointercalation oil properties of organoclays.
Understanding structural anisotropy and mechanical properties of Na-montmorillonite with crystalline swelling and uniaxial deformation under different hydration degrees

Bonan Li,Chengkai Li,Yilin Gui,Haifei Zhan,Yuantong Gu,Miao Yu,R. Kerry Rowe

DOI: https://doi.org/10.1016/j.compgeo.2024.106200

IF: 5.218

2024-03-03

Computers and Geotechnics

Abstract:Montmorillonite (MMT) is the main component of bentonite and its mechanical behaviour is sensitive to hydration degrees and structural anisotropy. In this study, molecular dynamics (MD) simulations were used to investigate the atomic structures and fracture behaviour of Na-MMT. The different deformation scenarios are applied to the Na-MMT with different hydration levels within the crystalline swelling phase of hydration. It is found that the mechanical behaviour of Na-MMT is significantly influenced by interlayer hydration degree and structural anisotropy. For example, the ultimate tensile strength and Young's modulus of Na-MMT exhibit decreasing trends with increasing hydration degrees. When tensile strain is applied along the two in-plane directions of the MMT layer, the fracture is observed in the silica-oxygen octahedra. The increase in hydration degree also raises the interlayer potential energy of the clay plate and reduces its stability. Meanwhile, buckling behaviour is observed under compression. These findings provide important insights into the origin of Na-MMT anisotropy, elucidating the complex interplay between the degree of hydration, structural anisotropy, and uniaxial deformation of Na-MMT. This work also provides key scientific insights for future studies of temperature effects, interlayer cation, and other mechanical responses.

computer science, interdisciplinary applications,geosciences, multidisciplinary,engineering, geological
A Coarse-Grained Interaction Model for Sodium Dominant Montmorillonite

Yaoting Zhang,Jeremy Oestreicher,W Jeffrey Binns,Scott Briggs,Chang Seok Kim,Laurent K Béland

DOI: https://doi.org/10.1021/acs.langmuir.2c02233

IF: 3.9

2022-11-01

Langmuir

Abstract:Montmorillonite is the main crystalline mineral present in bentonite. It is an absorbent, swelling material; the physical chemistry underlying its ability to absorb water and swell occurs at the nanoscale, governed by electrical double-layer interactions. In turn, absorption and swelling lead to important changes in the macroscopic transport properties of the clay. Mesoscale models can help us establish a link between these nanoscale processes and macroscale properties, notably by providing a detailed description of its pore network. Models on the scale of hundreds to thousands of nanometers are required, which cannot realistically be handled using traditional all-atom molecular dynamics simulations. This work presents a coarse-grained (CG) mesoscale model of sodium montmorillonite. In our model, montmorillonite platelets are represented by two types of particles: central nonhydrogen-bonded particles and edge hydrogen-bonding particles. The particle interactions are described by two-body potentials, which were optimized based on all-atom molecular dynamics simulations. Specifically, several potential mean force calculations involving dry and hydrated montmorillonite were performed, using the ClayFF potential to calculate interatomic forces. The CG model was validated by testing the scalability of the model, testing its ability to reproduce potentials of mean force reported elsewhere in the literature, and by comparing the calculated elastic properties of a system containing 1000 Na montmorillonite platelets to experimentally measured elastic properties of bentonite. The simulated elastic properties obtained using our mesoscale model agree with these experimental values.
Molecular Dynamics Simulations of Polyamide Membrane, Calcium Alginate Gel, and Their Interactions in Aqueous Solution

Yuan Xiang,Yaolin Liu,Baoxia Mi,Yongsheng Leng

DOI: https://doi.org/10.1021/la501811d

IF: 3.9

2014-07-24

Langmuir

Abstract:We perform molecular dynamics (MD) simulations to investigate the cross-linked polyamide (PA) membrane, the aggregation of alginate molecules in the presence of Ca(2+) ions, and their molecular binding mechanism in aqueous solution. We use a steered molecular dynamics (SMD) approach to simulate the unbinding process between a PA membrane and an alginate gel complex. Simulation results show that Ca(2+) ions are strongly associated with the carboxylate groups in alginate molecules, forming a web structure. The adhesion force between alginate gel and PA surface during unbinding originates from several important molecular interactions. These include the short-range hydrogen bonding and van der Waals attraction forces, and the ionic bridge binding that extends much longer pulling distances due to the significant chain deformations of alginate gel and PA membrane.

chemistry, multidisciplinary, physical,materials science
A molecular dynamics study of N‐A‐S‐H gel with various Si/Al ratios

Yun Chen,Jorge S. Dolado,Zhenming Li,Suhong Yin,Qijun Yu,Albina Kostiuchenko,Guang Ye

DOI: https://doi.org/10.1111/jace.18597

IF: 4.186

2022-06-10

Journal of the American Ceramic Society

Abstract:In this paper, the atomic structures of sodium aluminosilicate hydrate (N‐A‐S‐H) gels with different Si/Al ratios are studied by molecular dynamics simulation. N‐A‐S‐H gel model was obtained from the polymerization of Si(OH)4 and Al(OH)3 monomers with the use of reactive force field (ReaxFF). The simulated atomic structural features, such as the bond length, bond angle, and simulated XRD pattern of the gel structure are in good accordance with the experimental results in the literature. Si‐O‐Al is found to be preferred over Si‐O‐Si in the N‐A‐S‐H gel structure according to the amount of T‐O‐T bond angles and distribution of Si4(mAl). Pentacoordinate Al is identified in all simulated N‐A‐S‐H models. It provides a strong support to current knowledge that pentacoordinate Al in geopolymer does not only come from raw material. Furthermore, the structural analysis results also show that N‐A‐S‐H gel with lower Si/Al ratios has a more crosslinked and compacted structure. This article is protected by copyright. All rights reserved

materials science, ceramics
Revealing the microstructure of sodium-montmorillonite aqueous suspensions

Mohammad Shoaib,Shaihroz Khan,Omar B Wani,Jitendra Mata,Anthony J. Krzysko,Ivan Kuzmenko,Markus Bleuel,Lindsey K. Fiddes,Eric W. Roth,Erin R Bobicki

DOI: https://doi.org/10.48550/arXiv.2204.01869

2022-04-05

Abstract:Aqueous suspensions of geometrically anisometric (2D) sodium-montmorillonite (Na-Mt) particles display a sol-gel transition at very low solids concentrations. The underlying microstructure of the gel has remained a point of contention since the time of Irving Langmuir. An in-situ investigation encompassing length scales much larger than the individual particles is required to provide support for one of the two models proposed in the literature: 1) a percolated network governed by electrostatic attraction between platelets; and 2) a jammed suspension stabilized by repulsive electrostatic forces between particles. We settle this debate by comprehensively probing the microstructure of Na-Mt suspensions using ultra-small angle neutron/X-ray scattering and found that it is ordered and contains entities that are at least an order of magnitude larger than the individual particles. Complementary cryo-electron microscopy showed both the presence of domains having strong particle-particle ordering and regions of particle-particle aggregation. These data indicate 1) the presence of nematic domains, which refutes a purely attractive nature, and 2) assembly of particles, which refutes a purely repulsive nature. Na-Mt gels appear to have a hybrid microstructure with both attractive and repulsive domains.

Soft Condensed Matter
Effect of chain composition on the mechanical response of structural gel: A molecular dynamics simulation

Cui-Liu Fu,Xue-Zhi Jia,Zhao-Yan Sun,Li-Jia An

DOI: https://doi.org/10.1016/j.polymer.2014.07.006

IF: 4.6

2014-08-01

Polymer

Abstract:Polymer gels, defined either from the structural point of view (structural gel) or by their mechanical properties (mechanical gel), are ubiquitous in our daily life. In our previous work (J. Phys. Chem. B, 2011, 115, 11345), we reported that, the mechanical gel formed by strong solvophobic ABA block copolymers with fixed chain compositions shows a strong mechanical response, which meant the formed gel had a high modulus. In this work, we focus on the effect of chain composition on the relationship between structural gel and mechanical gel, where the chain length of block copolymer is lower than its entanglement chain length for simplicity. Our results show that the chain composition has a great effect on the mechanical response of the ABA copolymer solutions with a strong solvophobicity. On the other hand, for the structural gel formed by weak solvophobic block polymers, we do not find any strong mechanical responses even we change the chain composition in a wide range. Moreover, we find three typical gelation processes, companied with three kinds of different mechanical responses. These results may provide us an effective method to control the mechanical property of a polymer gel as expected.

polymer science
Rheological Behaviors of Na-montmorillonite Considering Particle Interactions: A Molecular Dynamics Study

Siqi Zhang,Daoyuan Tan,Honghu Zhu,Huafu Pei,Bin Shi

DOI: https://doi.org/10.1016/j.jrmge.2024.07.003

IF: 5.915

2024-01-01

Journal of Rock Mechanics and Geotechnical Engineering

Abstract:Understanding the rheology of bentonite suspensions is crucial for ensuring the safety of engineering practices. However, the rheological mechanisms of bentonite remain unclear due to the limitations of conventional experimental techniques, particularly in assessing the microscopic interactions between clay particles and their impact on rheological properties. In this paper, the rheological behaviors of Na-montmorillonite were studied with a focus on interparticle interactions. Both equilibrium molecular dynamics (MD) and non-equilibrium MD simulations were conducted to understand the physical properties of Na-montmorillonite under zero shear and various shear rates, respectively. The interaction between two parallel clay particles was determined in simulations, indicating that the classical Darjaguin-Landau-Verwey-Overbeek (DLVO) theory underestimates the interactions for a small separation distance. Na-montmorillonite exhibits a typical shear thinning behavior under shearing. However, as water content increases, it begins to behave more like liquid water. The yield stress of montmorillonite, as determined by the Bingham model, was found to be linearly related to the interaction pressures between clay particles. Besides MD simulations, the microstructure of clay suspension was further quantified using the separation distance and incline angle between non-parallel clay particles. Based on MD results and the quantified clay structure, a model was developed to estimate the yield stress of montmorillonite considering various influence factors, including electrolyte concentration, temperature, and solid fraction. Finally, from a comparison with calculated and experimental data, the results confirm the good performance of the proposed model. These findings provide significant insights for understanding the rheological soil behaviors and evaluating the yield stress of bentonite suspensions.
Molecular dynamics simulation of secondary sorption behavior of montmorillonite modified by single chain quaternary ammonium cations

Qian Zhao,Susan E Burns

DOI: https://doi.org/10.1021/es202115v

2012-04-03

Abstract:Organoclays synthesized from single chain quaternary ammonium cations (QAC) ((CH(3))(3)NR(+)) exhibit different mechanisms for the sorption of nonpolar organic compounds as the length of the carbon chain is increased. The interaction between a nonpolar sorbate and an organoclay intercalated with small QACs has been demonstrated to be surface adsorption, while partitioning is the dominant mechanism in clays intercalated with long chain surfactants. This study presents the results of a molecular dynamics (MD) simulation performed to examine the sorption mechanisms of benzene in the interlayer of three organoclays with chain lengths ranging from 1 to 16 carbons: tetramethylammonium (TMA) clay; decyltrimethylammonium (DTMA) clay; and hexadecyltrimethylammonium (HDTMA) clay. The basis of the overall simulation was a combined force field of ClayFF and CVFF. In the simulations, organic cations were intercalated and benzene molecules were introduced to the interlayer, followed by whole system NPT and NVT time integration. Trajectories of all the species were recorded after the system reached equilibrium and subsequently analyzed. Simulation results confirmed that the arrangement of the surfactants controlled the sorption mechanism of organoclays. Benzene molecules were observed to interact directly with the clay surface in the presence of TMA cations, but tended to interact with the aliphatic chain of the HDTMA cation in the interlayer. The simulation provided insight into the nature of the adsorption/partitioning mechanisms in organoclays, and explained experimental observations of decreased versus increased uptake capacities as a function of increasing total organic carbon (TOC) for TMA clay and HDTMA clay, respectively. The transition of sorption mechanisms was also quantified with simulation of DTMA clay, with a chain length between that of TMA and HDTMA. Furthermore, this study suggested that at the molecular level, the controlling factor for the ultimate sorption capacity is available surface sites in the case of TMA clay, and density of aliphatic chains within the interlayer space for HDTMA clay.

Molecular dynamics simulation and experimental study of micro‐structure and gel properties of single chain alkyl ammonium intercalated Na‐montmorillonite

A Molecular Dynamics Study on the Structural and Mechanical Properties of Pyrophyllite and M-Montmorillonites (M = Na, K, Ca, and Ba)

Microstructure of Different Chain Length Ionic Liquids Intercalated into Montmorillonite: A Molecular Dynamics Study

Microstructure and Process of Intercalation of Imidazolium Ionic Liquids into Montmorillonite

Molecular dynamics simulation of dodecyl dimethyl benzyl ammonium cation-intercalated montmorillonite

Molecular Dynamics Simulation of Alkylammonium-Intercalated Vermiculites

Interlayer structure and dynamics of alkylammonium-intercalated smectites with and without water: A molecular dynamics study

Molecular dynamics simulation of the initial stage induction of alkali-activated aluminosilicate minerals

Molecular Dynamics Study of Crystalline Swelling of Montmorillonite as Affected by Interlayer Cation Hydration

Influence of inorganic and organic salts on the hydration mechanism of montmorillonite based on molecular simulation

Molecular dynamics study of the effect of inorganic salts on the monolayer of four surfactants at the oil/water interface

Interlayer structure and dynamic properties of CTMAB–montmorillonite: experiment and molecular dynamics

Molecular Dynamics Insight into the Cointercalation of Hexadecyltrimethyl-Ammonium and Acetate Ions into Smectites

Understanding structural anisotropy and mechanical properties of Na-montmorillonite with crystalline swelling and uniaxial deformation under different hydration degrees

A Coarse-Grained Interaction Model for Sodium Dominant Montmorillonite

Molecular Dynamics Simulations of Polyamide Membrane, Calcium Alginate Gel, and Their Interactions in Aqueous Solution

A molecular dynamics study of N‐A‐S‐H gel with various Si/Al ratios

Revealing the microstructure of sodium-montmorillonite aqueous suspensions

Effect of chain composition on the mechanical response of structural gel: A molecular dynamics simulation

Rheological Behaviors of Na-montmorillonite Considering Particle Interactions: A Molecular Dynamics Study

Molecular dynamics simulation of secondary sorption behavior of montmorillonite modified by single chain quaternary ammonium cations