Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Performance of Magnesium, Mg‐Al Alloy and Silicon in Thermobaric Explosives – A Comparison to Aluminium

Energy and blast performance of beryllium in a model thermobaric composition in comparison with aluminum and magnesium

Semi‐closed Investigations of New Aluminized Thermobaric and Enhanced Blast Composites

A Method to Investigate the Confined Explosion of Thermobaric and Enhanced Blast Explosives

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

Research of detonation products of RDX/Al from the perspective of composition

Tuning the reactivity and energy release efficiency in aluminum alloy thermite by eutectic silicon

The effect of Mg(BH4)2 on the energy characteristics of RDX based aluminized explosives

Performance of TKX‐50 in Thermobaric Explosives

Laser Ignition and Combustion Characteristics of B-Al Compound Powder Without and with HMX: A Comparative Study

Effect of metal dust fuel at a low concentration on explosive/air explosion characteristics

On weak influence of aluminum powder size on its post-detonation reaction in different time scales

Study on laser ignition and combustion characteristics of micron-sized aluminum and Al-Mg alloys particles

OXIDIZER AND GAS-ENVIRONMENT EFFECTS ON AFTERBURNING REACTIONS AND EXPLOSION PERFORMANCES OF HMX-BASED THERMOBARIC EXPLOSIVES

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Effect of pressure and oxygen content on the ignition and combustion of Al–Mg alloy

Effect of low-concentration RDX dust on solid–liquid mixed fuel characteristics

Comparative Study on Combustion Behavior of Aluminum-Based Alloy Fuels and Aluminum Powder in Solid Propellants

Energy output performance of aluminized explosive containing Al/PTFE reactive materials

Estimating energy release performance of oxidizer-activated aluminum fuel particles under ultrafast stimulus

Hazard evaluation, explosion risk, and thermal behaviour of magnesium- aluminium alloys during the polishing process by using a 20-L apparatus, MIEA, and TGA