Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Combination of Group Method of Data Handling (GMDH) and Computational Fluid Dynamics (CFD) for Prediction of Velocity in Channel Intake

Numerical Simulation of Water Entry of Two-Dimensional Structures with Complex Geometry Using a CIP-based Model

Computation of Flow Past an In-Line Oscillating Circular Cylinder and a Stationary Cylinder in Tandem Using a CIP-Based Model

Performance Analysis of Dual-Channel Inward-Turning Inlets under Off-Design Conditions

Velocity prediction of nanofluid in a heated porous pipe: DEFIS learning of CFD results

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Numerical Study of Sedimentation and Flow Pattern at the Open Channel Intake

Experimental and Numerical Analysis of a Motorcycle Air Intake System Aerodynamics and Performance

A numerical model for calculating velocity distribution in cross-section of an open channel

Numerical Evaluation of Self‐Aeration in the Gelas Tunnel Intake: A Comparative Study Using VOF and Mixture Methods

AI-based predictive approach via FFB propagation in a driven-cavity of Ostwald de-Waele fluid using CFD-ANN and Levenberg–Marquardt

Measurement of intelligent computing via Levenberg Marquardt algorithm (LMA) for accurate prediction of fluid forces in a transient non-Newtonian thermal flow

Coarse-Grid Computational Fluid Dynamic (CG-CFD) Error Prediction using Machine Learning

Numerical Simulation on Helical Intake-Port 3D Flow Field of Diesel Engine

Maneuvering Prediction of A Vlcc Model Based on Cfd Simulation for Pmm Tests by Using A Circulating Water Channel

High-performance hybrid modeling chemical reactors using differential evolution based fuzzy inference system

Cfd Application on the Development of Circulating Water Channel

Improved Design Method for Hypersonic Intakes Using Pressure-Corrected Osculating Axisymmetric Flows Method

Prediction of multi-inputs bubble column reactor using a novel hybrid model of computational fluid dynamics and machine learning

Designing an Efficient Artificial Intelligent Approach for Estimation of Hydrodynamic Characteristics of Tapered Fluidized Bed from Its Design and Operating Parameters

Numerical study of an internal combustion engine intake process using a low Mach number preconditioned density-based method with experimental comparison