Abstract:Introduction: An important objective of orthodontic treatment is to obtain the correct mesiodistal angulation and faciolingual inclination for all teeth. Current techniques are based on crown angulation and inclination standards, and not enough attention has been given to the roots. In this study, we report the mesiodistal angulation and faciolingual inclination of each whole tooth including the root in patients with near-normal occlusion. Methods: We screened 1840 patients who had cone-beam computed tomography scans taken before treatment to obtain a sample of 76 patients with near-normal occlusion. Using our custom University of Sourthern California root vector analysis software program, we digitized the crown and root centers to determine the "true" long axis of each tooth from where the mesiodistal angulation and the faciolingual inclination were measured. Results: The means and standard deviations for the mesiodistal angulation and the faciolingual inclination of each whole tooth were calculated. The maxillary angulations of the teeth started from approximately 6 degrees for the central incisors, slightly increased for the lateral incisors, and peaked at 11 degrees for the canines; then it gradually decreased to just above 0 degrees for the first molars and eventually reached -6 degrees for the second molars. The mandibular angulations started from about 0 degrees for the incisors and increased to 17.5 degrees for the second molars. The maxillary inclination was the highest at 33.5 degrees for the central incisors, decreased to about 0 degrees at the second premolars, and then increased for the 2 molars. The mandibular inclination also was the highest at 26.5 degrees for the central incisors, decreased also to about 0 degrees at the second premolars, and continued to decrease for the 2 molars. For the opposing tooth pairs, the interdental mesiodistal angulations always remained within 10 degrees from one another, whereas the interdental faciolingual inclination increased from about 120 degrees for the incisors to about 180 degrees for the second premolars and the 2 molars. Conclusions: We obtained the average mesiodistal angulation and faciolingual inclination for each whole tooth measured from its long axis digitized on the cone-beam computed tomography volumetric images of 76 patients with near-normal occlusion. We found distinctive angulation and inclination relationships between the neighboring and opposing teeth. This information can be used in addition to the crown standards for positioning each whole tooth properly in the arches.( Am J Orthod Dentofacial Orthop 2012;141:604-17)

Can we estimate root axis using a 3-dimensional tooth model via lingual-surface intraoral scanning?

[A Pilot Study of Root Position in Orthodontic Diagnosis Model Set-Up].

Evaluation of in vivo digital root reconstruction based on anatomical characteristics of the periodontal ligament using cone beam computed tomography.

Mesiodistal angulation and faciolingual inclination of each whole tooth in 3-dimensional space in patients with near-normal occlusion.

Three-dimensional modelling and concurrent measurements of root anatomy in mandibular first molar mesial roots using micro-computed tomography

Three-dimensional Measurement of Periodontal Support During Surgical Orthodontic Treatment of High-Angle Skeletal Class III Malocclusion: A Retrospective Study.

Three-dimensional analysis of coronal root canal morphology of 136 permanent mandibular first molars by micro-computed tomography

Assessment of the coronal root canal morphology of permanent maxillary first molars using digital 3D-reconstruction technology based on micro-computed tomography data

[A Method for Rapid Extracting Three-Dimensional Root Model of Vivo Tooth from Cone Beam Computed Tomography Data Based on the Anatomical Characteristics of Periodontal Ligament].

[Measurement and Estimation of the Root Surface of Single-Root Teeth].

Occlusal and Labial/Buccal Approaches for Measuring MesioDistal Width of Teeth on Chairside Digitally Scanned Models

Accuracy of three-dimensional periodontal ligament models generated using cone-beam computed tomography at different resolutions for the assessment of periodontal bone loss

Evaluation of Three Methods for Constructing Craniofacial Mid-Sagittal Plane Based on the Cone Beam Computed Tomography

A Novel Three-Dimensional Quantitative Assessment Method for Abnormal Root Morphology of the Maxillary Premolars in Vivo on Cone-Beam Computed Tomography

Three-dimensional Localization of Impacted Canines and Root Resorption Assessment Using Cone Beam Computed Tomography

Three‐dimensional prediction of roots position through cone‐beam computed tomography scans‐digital model superimposition: A novel method

Optimum design of reference points distribution in three-dimensional reconstruction of dental model in intercuspal position

Accuracy Assessment of Three-dimensional Surface Reconstructions of in Vivo Teeth from Cone-beam Computed Tomography.

Three-dimensional evaluation of a virtual setup considering the roots and alveolar bone in molar distalization cases

Research progress on root position measurement methods in orthodontic treatment using cone beam CT

Accuracy of full arch three-dimensional dentition models from intraoral scanners