Abstract:Siloxanes are widely used in different applications: health care, dry cleaning, household products, paints and coatings, paper, personal care, for example. This explains their prevalence in the environment. Because of their volatile nature, most of the time they are dispersed in the atmosphere, but they can also be present in the slurry from landfills. During anaerobic digestion, when the temperature goes up to 60 degrees C, siloxanes are volatilized, forming part of the biogas. Operational problems using biogas to produce energy, heat and hydrogen have been identified. At high temperatures the siloxanes are transformed into silicate dioxide (commonly called sand transmission). These white deposits may adhere to metal or catalytic substrate surfaces, seriously reducing equipment efficiency, and this can be a reason for changing equipment warranties. Consequently, elimination of siloxanes has become very important. Unfortunately, relatively little information can be found on this subject. Nevertheless some authors have described different analytical methods for siloxane quantification, and recent studies have looked at the presence of siloxanes in landfills and the restriction on the energy recovery equipment using the biogas produced. The growing consumption of siloxanes and silicones in industrial processes consequently increase their prevalence in the environment, hampering the use of biogas as a source of 'green energy'. Therefore, the principal focus of this study is the treatment of siloxanes. Their elimination was carried out using an adsorption process with four different porous materials: activated carbon cloths (ACC), granular activated carbon (GAC), zeolite and silica gel. Two representative siloxane compounds were used in this study, hexamethyldisiloxane (L2) and octamethylcyclotetrasiloxane (D4). Adsorption kinetics and isotherms in batch reactors were performed. It was observed that the mass transfer into the porous material was more rapid for the activated carbon than for the zeolite and silica gel, congruent with the porous structure of the material. Moreover, it was found that D4 is more adsorbable than L2, due to possible interactions between the solid surface and the physical structure of the cyclic compound (D4). The influence of humidity and temperature were also studied. The increase in the temperature reduced the adsorption capacities. The influence of humidity on the adsorption was investigated under dry air and humid air at 70%. No significant difference in the adsorption capacities was found for the activated carbon and for the zeolite, but for the silica gel the mass transfer decreased considerably. For the adsorption isotherms, the maximal capacity of elimination was obtained with the activated carbon materials and was directly related to the porous structure. Thus activated carbon cloth was chosen to design the adsorption-desorption processes in a dynamic system. Thermal heating was used to achieve the regeneration process. Initial cycles have been accomplished and show the stability of the process.

Effects of Residual Silanol on Solid Phase Extraction of Organic Compounds to Octadecylsilyl Silica

SPEC Process III. Synthesis of a Macroporous Silica-based Crown Ether-impregnated Polymeric Composite Modified with 1-Octanol and its Adsorption Capacity for Sr(II) Ions and Some Typical Co-existent Metal Ions

Modification Of A Novel Macroporous Silica-Based Crown Ether Impregnated Polymeric Composite With 1-Dodecanol And Its Adsorption For Some Fission And Non-Fission Products Contained In High Level Liquid Waste

Impregnation synthesis of a novel macroporous silica-based crown ether polymeric material modified by 1-dodecanol and its adsorption for strontium and some coexistent metals

Laboratory Evaluation of the Use of Solvent Extraction for Separation of Hydrophobic Organic Contaminants from Surfactant Solutions During Surfactant-Enhanced Aquifer Remediation

Experimental Study on the Basic Characteristics of a Novel Silica-Based CMPO Adsorbent

<sup>2</sup>H NMR Studies of Simple Organic Groups Covalently Attached to Ordered Mesoporous Silica

Chromatographic behavior of packing materials for capillary electrochromatography with a coating of different immobilized polysiloxanes.

Impact of Degree of Ethoxylation on Sodium Lauryl Ether Sulfate Surfactant Adsorption onto Silicone-in-Water Emulsion Droplets

Effect of resin sulfonation on the retention of polar organic compounds in solid-phase extraction

Preparation of three structurally similar stationary phases with different ionizable terminal groups and evaluation of their retention performances under multiple modes in high performance liquid chromatography

Effects of synthesis conditions on particle size and pore size of spherical mesoporous silica

Arrangement of Monofunctional Silane Molecules on Silica Surfaces: Influence of Alkyl Chain Length, Head-Group Charge, and Surface Coverage, from Molecular Dynamics Simulations, X-ray Photoelectron Spectroscopy, and Fourier Transform Infrared Spectroscopy

Aggregation Behavior of Polyether Based Siloxane Surfactants in Aqueous Solutions: Effect of Alkyl Groups and Steric Hindrance.

Modified Mesoporous Silica For Efficient Siloxane Capture

Controllable organosilane monolayer density of surface bonding using silatranes for thiol functionalization of silica particles for liquid chromatography and validation of microanalytical method for elemental composition determination

Siloxane treatment by adsorption into porous materials

Effect of the Organic Substituent of Organotrialkoxylsilane on the Structure and Surface Properties of Silsesquioxanes

Structural Variety and Adsorptive Properties of Mesoporous Silicas with Immobilized Oligosaccharide Groups

Surfactant-Assisted Ethane-Bridged Silica Coating for Capillary Electrochromatography

Fabrication and evaluation of dodecyl imide maleopimaric acid glycidyl methacrylate ester modified silica with multiple retention mechanisms for reversed phase liquid chromatography