Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

Improvement and application of drilling and blasting techniques of anchor net (cable) spraying in rock roadways

Study on the Bolt-mesh-anchor Surrounding Mechanism of a Roadway in a Soft and Thick Rock Seam

Study on Anchor Cable instead of Single Hydraulic Prop Support in Advance Support of Deep Roadway

Application research on low cost support method for surrounding rock of broken section roadway in phosphate mine area

Technology of Controlled Blasting and Surrounding Rock Control for Mine Semi Coal and Rock Roadway

Study on Advanced Anchor - grouting Support of Mining Roadway in Close Lower Coal Seam

Dynamic Response Characteristics of Roadway Surrounding Rock and the Support System and Rock Burst Prevention Technology for Coal Mines

Reasonable Support Technology of Full-Stress Anchoring Technology of Advance Roadway: A Case Study

Grouting anchor cable active advanced support technology for mining roadways

Technology Research on Surrounding Rock Control for the High Roadway of Deeply Inclined Coal Seam

Research on High Strength and Pre-stressed Coupling Support Technology in Deep Extremely Soft Rock Roadway

Research on energy-absorption active control method for large deformation of tunnel surrounding rock through multi-fault fracture zone

Controlling large deformations in soft rock roadways with integrated anchor shotcrete and grouting techniques

Deep Mine Pressure Behavior and Combined Support Technology with Bolt Cable Wire

Study on Deformation Failure Mechanism and Control Technology of Surrounding Rock in Soft Rock Roadway

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting

Efficient Excavation and Support Cooperation Technology for Surrounding Rock of Deep Buried Long-Distance and Large Section Gob-Side Roadway: A Case Study

Full-Stress Anchoring Technology and Application of Bolts in the Coal Roadway

Study on Stability Control Mechanism of Deep Soft Rock Roadway and Active Support Technology of Bolt-Grouting Flexible Bolt

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

Synergistic Mechanism and Technology of Cable Bolt Resin Anchoring for Roadway Roofs with Weak Interlayers