Abstract:Conventional thermosets rely on petrochemical products, and cannot be reprocessed, recycled, or reshaped under mild conditions owing to their permanent, highly crosslinked structure. Although some of these materials are down-cycled into lower-value products, most thermosets are incinerated, landfilled, or otherwise unaccounted for (i.e. leakage), which intensifies the problem of resource shortage and environmental pollution. In this work, wheat straw lignin (Protobind 1000) was used as a raw material to prepare modified lignin by a non-catalytic reaction with t-butyl acetoacetate. The modified lignin was cross-linked with fatty acid diamine (PriamineTM 1075), and a fully biobased vitrimer material was successfully prepared. The vitrimers have high lignin content (40-50 wt%). The mechanical properties of these vitrimers could be adjusted by changing the density of the cross-linked network inside the material, which is determined by the ratio of modified lignin and diamine. In the case of elevated temperature (>100 oC), the dynamic chemical bonds (vinylogous urethane amine exchange) inside the material are activated, which allows the material to be recycled and reused. Rheology was used to study time and temperature-dependent stress relaxation dynamics. Experimental results show that the relaxation time typically ranges from 104 s at 150 °C to 9 s at 180 °C, exhibiting a rapid relaxation throughout the process without the addition of any catalyst. A potential application for this work is on-demand removable adhesives. The dry shear stress of the adhesive is 12.7 MPa (170 oC, 40 bar, 0.5 h), and the wet shear strength is similar under different conditions, with a minimum strength of 3.5 MPa. The superb adhesive strength mainly stems from the formation of abundant hydrogen bonds and mechanical interlocking between the adhesive and the wood. Combining the special solvent swelling behavior of the vitrimer material itself and the rapid exchange of dynamic chemical bonds of the material at high temperatures, we propose to use both solvent removal and heat removal methods to remove the adhesive, and the removed adhesive can be recycled. This work provides a case for biobased vitrimer to promote the development and utilization of advanced biobased thermoset materials.

Photocurable, Thermally Reprocessable, and Chemically Recyclable Vanillin-Based Imine Thermosets

Preparation of Styrene–Butadiene Rubber Vitrimers with High Strength and Toughness Through Imine and Hydrogen Bonds

A vanillin-derived hardener for recyclable, degradable and self-healable high-performance epoxy vitrimers based on transimination

Room temperature-curable, easily degradable, and highly malleable and recyclable vanillin-based vitrimers with catalyst-free bond exchange

Sustainable castor oil-based vitrimers: Towards new materials with reprocessability, self-healing, degradable and UV-blocking characteristics

A Biobased Epoxy Vitrimer with Dual Relaxation Mechanism: A Promising Material for Renewable, Reusable, and Recyclable Adhesives and Composites

High-performance and fully recyclable epoxy resins cured by imine-containing hardeners derived from vanillin and syringaldehyde

Degradable bio-based epoxy vitrimers based on imine chemistry and their application in recyclable carbon fiber composites

Bio-based Polyurethane Vitrimer with Imine Bonds: Excellent Thermo-Mechanical Properties and Heat Recovery

High-Strength and Multi-Recyclable Epoxy Vitrimer Containing Dual-Dynamic Covalent Bonds Based on the Disulfide and Imine Bond Metathesis

Sustainable Epoxy Vitrimers from Epoxidized Soybean Oil and Vanillin

Endowing Polythioester Vitrimer with Intrinsic Crystallinity and Chemical Recyclability

Preparation of lignin-based vinylogous urethane vitrimer materials and their potential use for on-demand removable adhesives

Build-To-Specification Vanillin and Phloroglucinol Derived Biobased Epoxy-Amine Vitrimers

Chemically Degradable Vitrimers Based on Divanillin Imine Diepoxy Monomer and Aliphatic Diamines for Enhanced Carbon Fiber Composite Applications

Imine-Containing Epoxy Vitrimer Cured by Active Ester: Properties and Theoretical Analysis

Bio-Based Epoxy Vitrimers with Excellent Properties of Self-Healing, Recyclability, and Welding

Toward versatile biobased epoxy vitrimers by introducing aromatic N-heterocycles with stiff and flexible segments

Fully rosin-based epoxy vitrimers with high mechanical and thermostability properties, thermo-healing and closed-loop recycling

Comprehensive itaconic acid-based vitrimers via one-pot inverse vulcanization

Fabricating a Repairable, Recyclable, Imine‐based Dynamic Covalent Thermosetting Resin with Excellent Water Resistance by Introducing Dynamic Covalent Oxime Bonds