Femtosecond Laser‐Induced Refractive Index Patterning in Inorganic/Organic Hybrid Films

Silvio Bonfadini,Tommaso Nicolini,Filippo Storti,Natalie Stingelin,Guglielmo Lanzani,Luigino Criante

DOI: https://doi.org/10.1002/adpr.202100257

2022-03-22

Advanced Photonics Research

Abstract:Advanced Photonics Research, EarlyView.

What problem does this paper attempt to address?

Strong Nonlinear Optics In On-Chip Lithium Niobate Photonic Molecules Fabricated By Femtosecond Laser

Min Wang,Ni Yao,Zhiwei Fang,Rongbo Wu,Jianhao Zhang,Jintian Lin,Wei Fang,Ya Cheng

DOI: https://doi.org/10.1364/CLEO_AT.2020.ATU3K.3

2020-01-01

Abstract:A photonic molecule (PM) composed of two strongly coupled lithium niobate microdisks was fabricated using femtosecond laser ablation followed by focused ion beam milling. Strong cascaded four-wave mixing and stimulated Raman scattering was demonstrated. (C) 2020 The Author(s)
Optical Properties of Highly Photosensitive Hybrid Sol-Gel Films

Jing Mao,Weidong Shen,Yi Yin,Yueguang Zhang,Xu Liu

DOI: https://doi.org/10.3788/col20100804.0435

IF: 2.56

2010-01-01

Chinese Optics Letters

Abstract:A new organic-inorganic hybrid material, which shows photo-induced reduction of refractive index as well as volume contraction, is prepared using a sol-gel method.This material is coated on a Si substrate by spin-coating to manufacture film.After irradiated by ultraviolet (UV) light with a deuterium lamp for 5 h, the thickness of film decreases largely by 55%, and the refractive index of film changes from 1.484 to 1.445 at 550 nm.The film's optical thickness exhibits an exponential change with the increasing irradiation time.Futhermore, the photo-patternning of the organic-inorganic hybrid film without any further process (wet etching and thermal curing) is performed utilizing the volume contraction on UV-light irradiation.This film has potential applications for fabrication of patterned filter array and apodizing filter by direct light writing, and also demonstrates good temperature stability and immunity to visible light exposure.
Thermally-induced nonlinear spatial shaping of infrared femtosecond pulses in nematic liquid crystals

di Pietro Vittorio Maria,Jullien Aurelie,Bortolozzo Umberto,Forget Nicolas,Residori Stefania

DOI: https://doi.org/10.48550/arXiv.1909.13098

2019-09-28

Optics

Abstract:An optically-induced thermal non-linear effect in a nematic liquid-crystal (E7) cell is evidenced through weak light-absorption by the ITO coating of an infrared pulsed femtosecond laser (m). Strong spatial self-phase modulation is generated, thus a multiple-ring pattern is observed in the far-field. The sign of the nonlinearity is changed depending on the laser polarization. The refractive index and thermal gradients are measured as a function of the laser intensity and we observe that the temperature can increase close to the nematic phase transition. The fidelity and stability of the process open new prospects for spatial shaping devices and delimits the operating wavelength range for ultrafast liquid-crystal based electro-optic application.
Femtosecond Laser Nano-Structuring of Transparent Materials

PG Kazansky,JR Qiu,Y Shimotsuma,E Bricchi,K Hirao

DOI: https://doi.org/10.1117/12.552356

2004-01-01

Abstract:New phenomena of anisotropic light scattering, anisotropic Cherenkov third-harmonic generation, photoinduced birefringence and anisotropic reflection from femtosecond direct-write structures are reviewed. The phenomena and recent direct observation reveal the smallest embedded structures ever created by light and new mechanism of light-matter interaction.
Tunable Index Back End of Line Platform for Enhanced Integrated Photonics

F. Y. Gardes,Cosimo Lacava,Kapil Debnath,T. D. Bucio,M. Banakar,S. Stankovic,A. Alattili,A. Z. Khokhar,S. Saito,P. Petropoulos,I. Molina-Fernandez,Robert Halir,A. Ortega-Monux,J. G. Wanguemert-Perez,Yang Chen,Jian-Jun He,Pavel Cheben,Jens H. Schmid

DOI: https://doi.org/10.1109/group4.2017.8082208

2017-01-01

Abstract:We demonstrate a back end of line compatible SiN based material with tunable refractive index enabling low optical loss, high non-linear Kerr response, low index photonic crystals, high efficiency couplers, low loss waveguides and temperature tolerant MUX for DWDM
Fabrication of High Refractive Index-Modulation Structures in Fused Silica by Femtosecond Laser Pulses

HC Guo,Y Li,X Wang,Y Fang,HB Jiang,H Yang,QH Gong

DOI: https://doi.org/10.1117/12.576903

2005-01-01

Abstract:We present the microfabrication of high refractive index-modulated structures written by line scan inside bulk of fused silica with a femtosecond laser at wavelength of 810 nm. The femtosecond laser beam, with duration between 130 fs and 500 fs at a repetition rate of 1 kHz. was focused through a microscope objective with numerical aperture (NA) of 0.10 or 0.25 into the sample. To fabricate high refractive index-modulated structures in fused silica, we investigated the dependence of refractive index change on laser Pulse energy, pulse duration, scan speed, and scanning repetitions. The results showed a "triangle region", with pulse duration of 130 fs to 230 fs and Pulse energy of 0.35 mu J to 1.5 mu J, for the fabrication of refractive index modulation Structures. The refractive index modulation was increased to 3 x 10(-3) after several scanning passes. Diffractive optical components Such as grid, square, circle gratings and Fresnel zone plates have been fabricated by direct writing technique. The structures Could be used as diffractive beam splitters, beam shaper and micro-tens.
Three-dimensional Nanostructuring of Transparent Materials by the Femtosecond Laser Irradiation

Y. Shimotsuma,M. Sakakura,S. Kanehira,J. Qiu,P. G. Kazansky,K. Miura,K. Fujita,K. Hirao

DOI: https://doi.org/10.2961/jlmn.2006.03.0006

2006-01-01

Journal of Laser Micro/Nanoengineering

Abstract:Femtosecond laser is a perfect laser source for materials processing when high accuracy and small structure size are required. Due to the ultra short interaction time and the high peak power, the process is generally characterized by the absence of heat diffusion and, consequently molten layers. Various induced structures have been observed inside glasses after the femtosecond laser irradiation. Here, we report the refractive index change, space-selective valence state manipulation of active ions and precipitation control of nanoparticles by a femtosecond laser in glasses. We have recently observed the three-dimensional nanostructuring such as a nano-grating and a nano-void inside a glass material by the single laser beam irradiation. The self-organized sub-wavelength periodic nanostructures are created by via a pattern of interference between the incident light field and the electric field of the bulk electron plasma wave. The mechanisms of the observed phenomena were also discussed. Furthermore, we observed the space-selective structural-phase transformation from diamond to amorphous structure which has electrically conductive property.
Micro-processing of Polymers and Biological Materials Using High Repetition Rate Femtosecond Laser Pulses

Li Ding

2009-01-01

Abstract:High repetition rate femtosecond laser micro-processing has been applied to ophthalmological hydrogel polymers and ocular tissues to create novel refractive and diffractive structures. Through the optimization of laser irradiation conditions and material properties, this technology has become feasible for future industrial applications and clinical practices. A femtosecond laser micro-processing workstation has been designed and developed. Different experimental parameters of the workstation such as laser pulse duration, focusing lens, and translational stages have been described and discussed. Diffractive gratings and three-dimensional waveguides have been fabricated and characterized in hydrogel polymers, and refractive index modifications as large as + 0.06 have been observed within the laser-irradiated region. Raman spectroscopic studies have shown that our femtosecond laser micro-processing induces significant thermal accumulation, resulting in a densification of the polymer network and increasing the localized refractive index of polymers within the laser irradiated region. Different kinds of dye chromophores have been doped in hydrogel polymers to enhance the two-photon absorption during femtosecond laser micro-processing. As the result, laser scanning speed can be greatly increased while the large refractive index modifications remain. Femtosecond laser wavelength and pulse energy as well as water and dye concentration of the hydrogels are optimized. Lightly fixed ocular tissues such as corneas and lenses have been micro-processed by focused femtosecond laser pulses, and refractive index modifications without any tissue-breakdown are observed within the stromal layer of the corneas and the cortex of the lenses. Living corneas are doped with Sodium Fluorescein to increase the two-photon absorption during the laser micro-processing, and laser scanning speed can be greatly increased while inducing large refractive index modifications. No evidence of cell death has been observed in or around the laser-induced refractive index modification regions. These results support the notion that femtosecond laser micro-processing method may be an excellent means of altering the refraction or higher order aberration content of corneal tissue without cell death and short-term tissue damage, and has been named as Intra-tissue Refractive Index Shaping (IRIS). The femtosecond laser micro-processing workstation has also been employed for laser transfection of single defined cells. Some preliminary results suggest that this method can be used to trace individual cells and record their biological and morphological evolution, which is quite promising in many biomedical applications especially in immunology science. In conclusion, high repetition rate femtosecond laser micro-processing has been employed to fabricate microstructures in ophthalmological hydrogels and ocular tissues. Its unique three-dimensional capability over transparent materials and biological media makes it a powerful tool and will greatly impact the future of…
Infrared photosensitivity in silica glasses exposed to femtosecond laser pulses

D. Homoelle,S. Wielandy,Alexander L. Gaeta,N. F. Borrelli,Charlene Smith

DOI: https://doi.org/10.1364/ol.24.001311

IF: 3.6

1999-09-15

Optics Letters

Abstract:We investigate the use of infrared femtosecond laser pulses to induce highly localized refractive-index changes in fused-silica glasses. We characterize the magnitude of the change as a function of exposure and measure index changes as large as 3x10(-3) and 5x10(-3) in pure fused silica and boron-doped silica, respectively. The potential of this technique for writing three-dimensional photonic structures in bulk glasses is demonstrated by the fabrication of a Y coupler within a sample of pure fused silica.

optics
Femtosecond Laser-Induced Inverted Microstructures Inside Glasses by Tuning Refractive Index of Objective's Immersion Liquid.

Fangfang Luo,Juan Song,Xiao Hu,Haiyi Sun,Geng Lin,Huaihai Pan,Ya Cheng,Li Liu,Jianrong Qiu,Quanzhong Zhao,Zhizhan Xu

DOI: https://doi.org/10.1364/ol.36.002125

2011-01-01

Abstract:We report the formation of inverted microstructures inside glasses after femtosecond laser irradiation by tuning the refractive index contrast between the immersion liquid and the glass sample. By using water as well as 1-bromonaphthalene as immersion liquids, microstructures with similar shape but opposite directions are induced after femtosecond laser irradiation. Interestingly, the elemental distribution in the induced structures is also inverted. The simulation of laser intensity distribution along the laser propagation direction indicates that the interfacial spherical aberration effect is responsible for the inversion of microstructures and elemental distribution.
Femtosecond Laser-Induced Two-Photon Polymerization: A New Avenue Towards Microoptics and Micromechanics

Qi-Dai Chen,Hong Xia,Dong Wu,Juan Wang,Xiao-Feng Lin,Ye Tian,Hong-Bo Sun

DOI: https://doi.org/10.1109/cleopr.2009.5292247

2009-01-01

Abstract:Various polymer micro-optical and mechanical components with complicated two and three-dimensional geometries have been prepared by femtosecond laser induced two-photon photopolymerization of resins, including aspheric micro lens and arrays, axicones, Dammann gratings, Fresnel lenses, Fractal zone plates, and integrated nanofiber sets.
Nanoscale local modification of PMMA refractive index by tip-enhanced femtosecond pulsed laser irradiation

Denis E. Tranca,Stefan G. Stanciu,Radu Hristu,Adrian M. Ionescu,George A. Stanciu

DOI: https://doi.org/10.1016/j.apsusc.2023.157014

2022-11-11

Abstract:Investigation techniques based on tip-enhanced optical effects, capable to yield spatial resolutions down to nanometers level, have enabled a wide palette of important discoveries over the past twenty years. Recently, their underlying optical setups are beginning to emerge as useful tools to modify and manipulate matter with nanoscale spatial resolution. We try to contribute to these efforts by reporting a method that we found viable to modify the surface refractive index of polymethyl methacrylate (PMMA), an acrylic polymer material. The changes in the refractive index are accomplished by focusing a femtosecond pulsed near-infrared laser beam on the apex of a metalized nano-sized tip, traditionally used in scanning probe microscopy (SPM) applications. The adopted illumination strategy yields circular-shaped modifications of the refractive index occurring at the surface of the PMMA sample, exhibiting a lateral size <200 nm, under 790 nm illumination, representing a four-fold increase in precision compared to the current state-of-the-art. The light intensity enhancement effects taking place at the tip apex makes possible achieving refractive index changes at low laser pulse energies (<0.5 nJ), which represents two orders of magnitude advantage over the current state-of-the art. The presented nanoimprinting method is very flexible, as it can be used with different power levels and can potentially be operated with other materials. Besides enabling modifications of the refractive index with high lateral resolution, this method can pave the way towards other important applications such the fabrication of photonic crystal lattices or surface waveguides.

Optics
Nanofabrication in transparent materials with a femtosecond pulse laser

Yasuhiko Shimotsuma,Kazuyuki Hirao,Jianrong Qiu,Kiyotaka Miura

DOI: https://doi.org/10.1016/j.jnoncrysol.2005.11.060

IF: 4.458

2006-01-01

Journal of Non-Crystalline Solids

Abstract:Femtosecond lasers have been applied for materials processing when high accuracy and small structure size are required. Various induced structures have been observed inside glasses after the femtosecond laser irradiation. We report the femtosecond laser induced refractive-index change, space-selective valence state change of active ions, formation of nanograting, and precipitation and distribution of nanoparticles. We systematically studied the morphology of structures that are induced in the bulk of transparent materials by the tightly focused femtosecond laser radiation. Rugby-ball-like asymmetric induced structures were observed inside Ag+-doped silicate glass. These structures are due to the aggregation of Ag nanoparticles at the depth of the focal point. The size of the induced structure depended on the time interval between successive femtosecond laser pulses. In the case of zinc-tellurite glass, TeO2 rich parts were formed in the center of the focal spot, while zinc migrated to the outside. The mechanisms of the observed phenomena are discussed.
Spatial Photo‐Patterning of Nematic Liquid Crystal Pretilt and its Application in Fabricating Flat Gradient‐Index Lenses

Alvin Modin,Robert L. Leheny,Francesca Serra

DOI: https://doi.org/10.1002/adma.202310083

IF: 29.4

2024-02-03

Advanced Materials

Abstract:Liquid crystals offer a dynamic platform for developing advanced photonics and soft actuation systems due to their unique and facile tunability and reconfigurability. Achieving precise spatial patterning of the liquid crystal alignment is critical to developing electro‐optical devices, programmable origami, directed colloidal assembly, and controlling active matter. Here, we demonstrate a simple method to achieve continuous three‐dimensional control of the directions of liquid crystal mesogens using a two‐step photo‐exposure process. In the first step, polarized light sets the orientation in the plane of confining substrates; the second step uses unpolarized light of a prescribed dose to set the out‐of‐plane orientation. The method enables smoothly varying orientational patterns with sub‐micrometer precision. As a demonstration, we design gradient‐index lenses with parabolic refractive index profiles that remain stable without external electric fields. We characterize the lenses' focal length and sensitivity to light polarization through experimental and numerical methods. Our findings pave the way for developing next‐generation photonic devices and actuated materials, with potential applications in molecular self‐assembly, re‐configurable optics, and responsive matter. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Femtosecond laser microfabrication of micro-optic elements in glass

Yan Li,Hongbing Jiang,Hong Yang,Qihuang Gong

IF: 2.56

2005-01-01

Chinese Optics Letters

Abstract:Micro-optic elements have been fabricated in silica and soda-lime glass with femtosecond laser pulses. The dependence of refractive index change on pulse duration, pulse energy and scan passes is investigated and a Fresnel zone plate is induced. A permanent computer-generated hologram encoded by the detour phase method is directly written by microexplosion. The stored image is reconstructed with a collimated He-Ne laser beam. Three-dimensional microchannels are drilled by water-assisted ablation. At low incident pulse energy, only one transverse microhole is observed. At high incident pulse energy, multiple transverse microholes are simultaneously drilled.
3D Laser Nanoprinting of Optically Functionalized Structures with Effective-Refractive-Index Tailorable TiO2 Nanoparticle-Doped Photoresin

Shichao Song,Yijie Li,Zhuofan Yao,Jie Li,Xiangping Li,Yaoyu Cao

DOI: https://doi.org/10.3390/nano12010055

IF: 5.3

2021-12-25

Nanomaterials

Abstract:The advanced direct laser printing of functional devices with tunable effective index is a key research topic in numerous emerging fields, especially in micro-/nano-optics, nanophotonics, and electronics. Photosensitized nanocomposites, consisting of high-index materials (e.g., titanium dioxide, TiO2) embedded in polymer matrix, are emerging as attractive platforms for advanced additive manufacturing. Unfortunately, in the currently applied techniques, the preparation of optically functionalized structures based on these photosensitized nanocomposites is still hampered by many issues like hydrolysis reaction, high-temperature calcinations, and, especially, the complexity of experimental procedures. In this study, we demonstrate a feasible strategy for fabricating micro-/nanostructures with a flexibly manipulated effective refractive index by incorporating TiO2 nanoparticles in the matrix of acrylate resin, i.e., TiO2-based photosensitized nanocomposites. It was found that the effective refractive index of nanocomposite can be easily tuned by altering the concentration of titanium dioxide nanoparticles in the monomer matrix. For TiO2 nanoparticle concentrations up to 30 wt%, the refractive index can be increased over 11.3% (i.e., altering from 1.50 of pure monomer to 1.67 at 532 nm). Based on such a photosensitized nanocomposite, the grating structures defined by femtosecond laser nanoprinting can offer vivid colors, ranging from crimson to magenta, as observed in the dark-field images. The minimum printing width and printing resolution are estimated at around 70 nm and 225 nm, indicating that the proposed strategy may pave the way for the production of versatile, scalable, and functionalized opto-devices with controllable refractive indices.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
High-Performance Birefringence of Periodic Nanostructures in FTO Thin Film Fabricated by IR-UV Femtosecond Laser

Fengzhuo Zhang,Long Chen,Yuchan Zhang,Qilin Jiang,Donghai Feng,Shian Zhang,Tianqing Jia,Zhenrong Sun,Hongxing Xu

DOI: https://doi.org/10.3389/fphy.2022.861389

IF: 3.718

2022-03-16

Frontiers in Physics

Abstract:By using infrared to ultraviolet (IR-UV) femtosecond laser directing, periodic nanostructures were efficiently fabricated on an F-doped tin oxide (FTO) film with a thickness of 650 nm. The morphology of the nanostructures and duty cycle were studied in detail by changing the laser fluence and scanning speed, where three lasers with central wavelengths of 343, 515, and 1,030 nm were used in the experiments. Under the 515 nm laser irradiation with scanning speed of 0.01 mm/s and laser fluence of 23 mJ/cm 2 , the periods Λ is 172 nm, the ablated nanogroove with width w 2 is 52 nm, the birefringence Δ n reached a maximum of 0.21, and the phase retardance was up to 135 nm. The morphology of the nanostructures and the birefringence effects of the FTO film prepared by a femtosecond laser at wavelengths of 1,030 and 343 nm were also studied, where the phase retardance of the nanostructured FTO film was much lesser than for the 515 nm laser because the thickness of the nanoripples layer, and, thus, the duty cycle of periodic nanoripples was smaller. Finally, a large-area FTO film with periodic nanostructures was fabricated efficiently by direct laser writing using a 515 nm fs laser beam focused via a cylindrical lens, and demonstrated the characteristics of a quarter-wave plate for 532 nm light.

physics, multidisciplinary
Electro-optic spatial light modulator from an engineered organic layer

Ileana-Cristina Benea-Chelmus,Maryna L. Meretska,Delwin L. Elder,Michele Tamagnone,Larry R. Dalton,Federico Capasso

DOI: https://doi.org/10.1038/s41467-021-26035-y

IF: 16.6

2021-10-11

Nature Communications

Abstract:Abstract Tailored nanostructures provide at-will control over the properties of light, with applications in imaging and spectroscopy. Active photonics can further open new avenues in remote monitoring, virtual or augmented reality and time-resolved sensing. Nanomaterials with χ (2) nonlinearities achieve highest switching speeds. Current demonstrations typically require a trade-off: they either rely on traditional χ (2) materials, which have low non-linearities, or on application-specific quantum well heterostructures that exhibit a high χ (2) in a narrow band. Here, we show that a thin film of organic electro-optic molecules JRD1 in polymethylmethacrylate combines desired merits for active free-space optics: broadband record-high nonlinearity (10-100 times higher than traditional materials at wavelengths 1100-1600 nm), a custom-tailored nonlinear tensor at the nanoscale, and engineered optical and electronic responses. We demonstrate a tuning of optical resonances by Δ λ = 11 nm at DC voltages and a modulation of the transmitted intensity up to 40%, at speeds up to 50 MHz. We realize 2 × 2 single- and 1 × 5 multi-color spatial light modulators. We demonstrate their potential for imaging and remote sensing. The compatibility with compact laser diodes, the achieved millimeter size and the low power consumption are further key features for laser ranging or reconfigurable optics.

multidisciplinary sciences
Digital and Gradient Refractive Index Planar Optics by Nanoimprinting Mesoporous Silicon

Anna L. Hardison,Tahmid H. Talukdar,Ivan I. Kravchenko,Judson D. Ryckman

DOI: https://doi.org/10.1002/adom.202201597

IF: 9

2022-11-12

Advanced Optical Materials

Abstract:A method for patterning refractive index distributions, n(x,y), on the surface of a chip is demonstrated based on nanoimprinting mesoporous silicon and applied to realize functional planar optical components with digital and gradient refractive index profiles. Device demonstrations include effective medium waveguides and flat effective medium micro‐lens arrays. This work opens a new route for planar optical design and fabrication. We report the realization of digital and gradient index flat‐optics and planar waveguides using the 'nanoimprinting refractive index' (NIRI) technique applied to mesoporous silicon. This technique combines the distinct optical and mechanical metamaterial qualities of mesoporous silicon, including its widely tunable effective refractive index and ability to undergo plastic deformation with a near zero Poisson ratio. Nanoimprinting with premastered and reusable stamps containing analog or digital features enables the continuous or discontinuous patterning of refractive index with high contrast Δn ≥ 0.8 and subwavelength resolution. Using NIRI we experimentally demonstrate a wavefront shaping flat microlens array operating in the visible (405–635 nm) and mesoporous silicon and silica waveguides operating near 1310 nm. This study demonstrates the viability of patterning arbitrary refractive index distributions, n(x,y), on the surface of a chip while circumventing the challenges and limitations of top‐down lithographic techniques – thus opening a low‐cost and scalable approach for the realization of advanced planar optical technologies.

materials science, multidisciplinary,optics
Laser-induced erasable patterns in a N* liquid crystal on an iron doped lithium niobate surface

Atefeh Habibpourmoghadam,Liana Lucchetti,Dean R. Evans,Victor Y. Reshetnyak,Faissal Omairat,Samuel L. Schafforz,Alexander Lorenz

DOI: https://doi.org/10.1364/oe.25.026148

IF: 3.8

2017-10-12

Optics Express

Abstract:A chiral nematic (N*) liquid crystal (LC) was hybridized with a z-cut iron doped lithium niobate (Fe:LN) substrate and exposed with a focused continuous wave diode laser beam. The N* LC layer was confined with a cover glass to provide a homogeneous LC layer thickness. Two distinct kinds of test cells were investigated, one with an uncoated glass covering slip and one with an indium tin oxide (ITO) coated cover glass. Photo generated electric fields (generated in the Fe:LN) resulted in a localized defect formation and textural transitions in the N* LC. Due to field confinement, the field induced responses were more localized in samples with ITO coated cover glasses. By scanning the laser beam on programmed trajectories, formation of persistent patterns could be achieved in the N* LC layer. Polarized optical microscopy of the exposed samples revealed that these patterns consisted of adjacent circular Frank-Pryce defects. Exposure with a slightly defocused laser beam could be applied selectively to erase these patterns. Thus, a promising method is reported to generate reconfigurable patterns, photonic motives, and touch sensitive devices in a hybridized N* LC with micron accuracy.

optics

Femtosecond Laser‐Induced Refractive Index Patterning in Inorganic/Organic Hybrid Films

Strong Nonlinear Optics In On-Chip Lithium Niobate Photonic Molecules Fabricated By Femtosecond Laser

Optical Properties of Highly Photosensitive Hybrid Sol-Gel Films

Thermally-induced nonlinear spatial shaping of infrared femtosecond pulses in nematic liquid crystals

Femtosecond Laser Nano-Structuring of Transparent Materials

Tunable Index Back End of Line Platform for Enhanced Integrated Photonics

Fabrication of High Refractive Index-Modulation Structures in Fused Silica by Femtosecond Laser Pulses

Three-dimensional Nanostructuring of Transparent Materials by the Femtosecond Laser Irradiation

Micro-processing of Polymers and Biological Materials Using High Repetition Rate Femtosecond Laser Pulses

Infrared photosensitivity in silica glasses exposed to femtosecond laser pulses

Femtosecond Laser-Induced Inverted Microstructures Inside Glasses by Tuning Refractive Index of Objective's Immersion Liquid.

Femtosecond Laser-Induced Two-Photon Polymerization: A New Avenue Towards Microoptics and Micromechanics

Nanoscale local modification of PMMA refractive index by tip-enhanced femtosecond pulsed laser irradiation

Nanofabrication in transparent materials with a femtosecond pulse laser

Spatial Photo‐Patterning of Nematic Liquid Crystal Pretilt and its Application in Fabricating Flat Gradient‐Index Lenses

Femtosecond laser microfabrication of micro-optic elements in glass

3D Laser Nanoprinting of Optically Functionalized Structures with Effective-Refractive-Index Tailorable TiO2 Nanoparticle-Doped Photoresin

High-Performance Birefringence of Periodic Nanostructures in FTO Thin Film Fabricated by IR-UV Femtosecond Laser

Electro-optic spatial light modulator from an engineered organic layer

Digital and Gradient Refractive Index Planar Optics by Nanoimprinting Mesoporous Silicon

Laser-induced erasable patterns in a N* liquid crystal on an iron doped lithium niobate surface