Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Flow boiling pressure drop characteristics in a multi-microchannel heat sink

Theoretical and Experimental Research on Flow Boiling Heat Transfer in Microchannels for IGBT Modules

Pressure Drop Characteristics of R134a During Flow Boiling in a Single Rectangular Micro-Channel

Flow Boiling Instability and Pressure Drop Characteristics Based on Micro-Pin-finned Surfaces in a Microchannel Heat Sink

Pressure drop correlation for subcooled flow boiling in micro-channel heat sink

Two-phase flow boiling in a microfluidic channel at high mass flux

Flow Boiling Heat Transfer and Pressure Drop Characteristics of Water in a Copper Foam Fin Microchannel Heat Sink

Heat transfer coefficient and pressure drop of water flow boiling in porous open microchannels heat sink

On the Operational Parameters Effects on Two-Phase Pressure Drop Characteristics of Reentrant Copper Microchannels

Experimental Study and Correlation Development for the Two-Phase Frictional Pressure Drop of Flow Boiling in Copper Foam Fin Microchannels

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

Flow Pattern Study and Pressure Drop Prediction of Two-Phase Boiling Process in Different Surface Wettability Microchannel

An experimental study on two-phase flow patterns and heat transfer characteristics during boiling of R134a flowing through a multi-microchannel heat sink

Fluid flow and heat transfer characteristics of a microstructured microchannel heat sink under flow boiling condition

Experimental Investigation of Pressure Drop Characteristics of Flow Boiling in Mini-channels

Experimental study on flow boiling characteristics of R134a inside high-heat-flux microchannels

Experimental Study on Flow Boiling Pressure Drop and Flow Instabilities of Reentrant Micro-Channels

Pressure drop of R134a in mini channels with micro pin fins during flow boiling

Experimental Study on Boiling Heat Transfer and Pressure Drop Characteristics of Hybrid Jet Microchannel Heat Sink

Flow Boiling Pressure Drop Characteristics in Rectangular Channels under Uniform and Non-Uniform Heating

Experimental study on two-phase pressure drop and flow boiling heat transfer in a micro pin fin channel heat sink under constant heat flux