Abstract:<p>A co-precipitation hardened medium-Mn steel with respective NiAl and Cu-rich particles in dual phases (austenite and ferrite) has been designed by using a quenching-partitioning-tempering (QPT) treatment. The influences of co-precipitates on the elasto-plastic transition and strain compatibility has been investigated based on the micro-mechanical behavior of constituent phases, the evolution of lattice strain and stress components. Compared to the Cu-Free steel, in which single NiAl precipitates form in ferrite, co-precipitation in the Cu-Added steel results in an improved strain compatibility between austenite (γ) and ferrite (α). The lattice strains of both γ and α phases show similar evolutions during the entire strain regime, and a homogeneous elasto-plastic deformation occurs together with a continuous yielding and weak transient of strain hardening rate. The improved strain compatibility leads to an alleviation of strain localization in the phase interfaces, so that the overall back stress increases slowly with the tensile strain increasing during the whole plastic deformation process, although the transformation-induced plasticity (TRIP) effect of the Cu-Added steel only occurs at low strains (<5%) due to the low mechanical stability of the retained austenite. In contrast, a non-continuous yielding of the constituent phases occurs in the Cu-Free steel leads to strong strain transfer across the α/γ interfaces due to a low deformation compatibility between austenite and ferrite. High internal stress in the phase interfaces results in easy damage-crack formation, but it can be accommodated by the TRIP effect which dominates in large strains, resulting in back stress decreasing and effective stress hardening during the subsequent deformation stage. However, the introduction of hydrogen can aggravate the dislocation accumulation and strain transfer between austenite and ferrite; thus, hydrogen-induced cracks (HICs) are prone to nucleate at the α/γ interfaces while the TRIP effect is not significant, leading to premature failure and significant elongation loss (85.4%) of the Cu-Free steel. Therefore, the improved strain compatibility of the Cu-Added steel contributes to a better resistance to hydrogen embrittlement, although both medium Mn steels possess similar tensile strength (1 GPa) and elongation (25%) values.</p>

Hydrogen embrittlement resistance of pre-strained ultra-high-strength low alloy TRIP-aided steel

Effect of shearing prestrain on the hydrogen embrittlement of 1180 MPa grade martensitic advanced high-strength steel

Effect of pre-strain on hydrogen embrittlement of high manganese steel

Hydrogen embrittlement of a cold-rolled Al-containing medium-Mn steel: Effect of pre-strain

Mechanical Behaviors of Microalloyed TRIP-Assisted Annealed Martensitic Steels under Hydrogen Charging

Effect of pre-strain on mechanical properties and hardening behavior of TRIP steel

Effect of Hydrogen on Fatigue Life and Fracture Morphologies of TRIP-Aided Martensitic Steels with Added Nitrogen

Analysis of enhanced hydrogen embrittlement fracture for pre-strain hardening 2205 duplex stainless steel

Irreversible hydrogen embrittlement study of B1500HS high strength boron steel

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Effect of pre-strain on hydrogen induced cracking of PAW welded 304 austenitic stainless steel

Enhanced stretch flangeability and crack propagation behavior of an 1100 MPa grade TRIP-aided bainitic ferrite steel

Anisotropic effect of pre-strain on hydrogen embrittlement susceptibility in a stable austenitic stainless steel

Effects of Mean Normal Stress and Microstructural Properties on Deformation Properties of Ultrahigh-Strength TRIP-Aided Steels with Bainitic Ferrite and/or Martensite Matrix Structure

Influence Of Low Temperature Prestrain On Hydrogen Gas Embrittlement Of Metastable Austenitic Stainless Steels

Hydrogen embrittlement mechanisms in advanced high strength steel

Effect of pre-strain on critical conditions for hydrogen-induced delayed cracking and crack nucleation characteristic of DP1180 steel

Hydrogen-induced hardening of a high-manganese twinning induced plasticity steel

Homogeneous elasto-plastic deformation and improved strain compatibility between austenite and ferrite in a co-precipitation hardened medium Mn steel with enhanced hydrogen embrittlement resistance

Mitigating hydrogen embrittlement of advanced high-strength steel by controlling carbides (cementite and alloy carbides) and microstructural modification

Effect of Strain-Induced Martensite on Hydrogen Embrittlement of Austenitic Stainless Steels Investigated by Combined Tension and Hydrogen Release Methods