Abstract:Abstract To determine the characteristics of air leakage concerning a “Y” type ventilation in gob-side entry retaining with roof cutting, pressure relief, and the law of a resulted gas accumulation (GA), research is conducted by employing the CFD simulation incorporated with the gauged parameters of working face (WF) mining to analyze the air leakage of “Y” type ventilation. For this purpose, the 1201 fully mechanized coal mining face in the south Wu mining location of the Daxing coal mine is taken as an illustrative example to study the air leakage in the “Y” type ventilation. So, the gas concentration (GC) issue surpassing the limit in the upper corner of the goaf was simulated. The results show that the goaf is formed into an open space when roof cutting and pressure relief technology along the goaf is implemented. The air pressure at the upper corner of the WF would be the lowest, which is only 1.12 Pa. The airflow of air leakage under a pressure difference would move from the gob-side entry retaining to the goaf. Moreover, the simulation of mine ventilation indicates that the volume of air leakage positively correlates with the length of gob-side entry retaining. When the WF is advanced 500 m ahead, the maximum volume of air leakage would reach 247 m 3 /min within the range of 500–1300 m, and then the rate of air leakage gradually would decrease. When the WF is advanced at 1300 m, the air leakage would become the smallest, which is 175 m 3 /min. When gas control is under consideration, the effect of gas extraction would be best with the buried pipe whose depth and diameter are set to 4.0 m and 400 mm, respectively. So, the GC in the upper corner would become 0.37%. After the high-level borehole with a 120 mm diameter is mined, the GC in the deep goaf decreased to 3.52%, and the GC at the upper corner became further reduced to 0.21%. While the high-level borehole gas is extracted by employing the extraction system of the high-concentration gas, the extraction system of low-concentration gas is utilized to extract the upper corner gas of the WF, thus, the problem of gas overrun was resolved satisfactorily. During the recovery period of the mining, the GC at each gauging point was less than 0.8%, which effectively guided the secure production in the Daxing coal mine and provided a theoretical foundation to control gas overrun during the mining process.

Research and application of gas overrun prevention technology by hydraulic reaming

Research on the Coal Seam Permeability-Increasing Technology via High-Pressure Water Jet Reaming and Its Application

Research and Application of Coal Seam Permeability Improvement Technology by Sectional Directional Hydraulic Fracturing

Research and Engineering Practice of Gas Accurate Drainage Technology with Hole-substituted Roadway in Mabao Coal Mining Area of Jinneng Group

Gas comprehensive prevention and control technology and practice in outburst mine

Research and application of high-pressure water jets drilling and repairing failure drainage borehole for enhancing coalbed methane recovery in underground coal mines

Coal breakage impact by high-pressure water jet and induced pressure relief and permeability enhancement by hydraulic flushing cavity: mechanism and application

Gas Control Technology of Fully Mechanized Caving Face of Hard Desorbing Coal Seam

Research on gas drainage technology and equipment of high-level directional drilling in coal mine

Mechanism and Prevention Technologies of Reservoir Gas Disaster in Abandoned Oil Well of Coal Mine

A novel technology for high-efficiency borehole-enlarging to enhance gas drainage in coal seam by mechanical cutting assisted by waterjet

Application of integrated drilling and stamping technology in gas extraction through layer drilling

Research on Optimization of Large Flow Hydraulic Punching Process in Zhaozhuang Mine

Pulsating hydraulic fracturing technology in low permeability coal seams

Gas Migration Law and Precision Extraction in Close Distance Coal Seam Goaf: A Case Study

Research on the Abnormal Occurrence Characteristics of Gas in Impermeable Small Fault Group and Its Control Technology

Study on a High-Efficiency Mining Technology System for Gas Outburst in Coal Seams—Example of an H Coal Mine

Coal and gas outburst control using uniform hydraulic fracturing by destress blasting and water-driven gas release

Research and field application of ultra high pressure hydraulic cutting technology in Gaohe coal minethe title of your paper here

Research on controlling gas overrun in a working face based on gob-side entry retaining by utilizing ventilation type “Y”