Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

The thickness of the microcapsule layers of the SPI nanofibrils

Designer Fibers from 2D to 3D – Simultaneous and Controlled Engineering of Morphology, Shape and Size

Properties and morphology of poly(lactic acid)/soy protein isolate blends

Morphology of Soy Protein Isolate at Oil/Water and Oil/Air Interfaces

Study of the Effect of Membrane Thickness on Microcapsule Strength, Permeability, and Cell Proliferation

Measurement of particle diameter of Lactobacillus acidophilus microcapsule by spray drying and analysis on its microstructure

Fabrication and characterization of succinylated and glycosylated soy protein isolate and its self-assembled nanogel

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Simple production of cellulose nanofibril microcapsules and the rheology of their suspensions

Release of small hydrophilic molecules from polyelectrolyte capsules: effect of the wall thickness

Layer-by-layer Assembly of Microcapsules and Their Biomedical Applications

Preparation and Characterization of Soy Protein Isolate-Based Nanocomposite Films with Cellulose Nanofibers and Nano-Silica via Silane Grafting

Effects of High Crystallinity on the Molecular Mobility in Poly(lactic acid)-Based Microcapsules

Multilayer Capsules with Cell-like Topology: Fabrication and Spontaneous Loading of Various Substances in Aqueous and Ethanol Solutions

Preparation and characterization of soybean protein isolate-dextran conjugate-based nanogels

Uptake of microcapsules with different stiffness and its influence on cell functions

Microcapsules of poly(methyl metharcylate) containing epoxy resin and multi-walled carbon nanotubes

Real-time particle size analysis using focused beam reflectance measurement as a process analytical technology tool for continuous microencapsulation process

Experimental and numerical investigation on the effect of core-shell microcapsule sizes on mechanical properties of microcapsule-based polymers

Fabrication, encapsulation and controlled release of multilayer capsule based on thermosensitivity and host‐guest interaction

Microstructure and permeability of hollow microcapsules produced from faba bean 11s protein