Abstract:This paper introduces a 4‐channel 24‐ to 28‐GHz RF front‐end MIMO system designed for 5G applications. The TX and RX chips are fabricated using 130‐nm SiGe BiCMOS technology. The measurement results of a single‐channel indicate a gain of 15.5‐dB and −25‐dBm IP1dB for the RX chip and 26.5‐dB and 10‐dBm OP1dB for the TX chip while each chip occupies 0.83 mm2 . The RX chip exhibits a measured NF of 4.3 dB at 26 GHz. Both Tx and Rx chips achieve 6‐bit phase control and 4‐bit amplitude control with low RMS phase error of 2.6° and gain error of 0.3 dB. Low RMS gain and phase errors over a wide bandwidth are attributed to the high precision DAC employed in the control of VGA and PS. This paper introduces a 4‐channel 24‐ to 28‐GHz RF front‐end MIMO system designed for 5G applications. The transmitter (Tx) and receiver (Rx) chips are fabricated using 130‐nm SiGe BiCMOS technology. The chips contain a 6‐bit phase shifter (PS), 1‐bit attenuator (ATT), 3‐bit variable gain amplifier (VGA), serial peripheral interface (SPI), Wilkinson combiner, power amplifier (PA), and low noise amplifier (LNA). The designed vector‐sum PS, employing a current DAC for semi‐digitization, achieves a 6‐bit phase resolution with minimal root‐mean‐square (RMS) phase error. This design choice allows for the high bit control of the current DAC within a compact chip area. Four‐bit amplitude control is obtained with VGA and ATT. The VGA provides 8‐dB amplitude range while ATT enlarges overall amplitude control with additional 8 dB. L‐R‐L phase compensation technique is utilized to reduce the phase error that arises from ATT. The sub‐blocks are designed to operate with low DC power such that the DC power consumption of overall RX and TX is 50 and 97 mW, respectively. The measurement results of a single‐channel indicate a gain of 15.5‐dB and −25‐dBm IP1dB for the RX chip and 26.5‐dB and 10‐dBm OP1dB for the TX chip while each chip occupies 0.83 mm2 . The RX chip exhibits a measured noise figure (NF) of 4.3 dB at 26 GHz. Both Tx and Rx chips achieve 6‐bit phase control and 4‐bit amplitude control with low RMS phase error of 2.6° and gain error of 0.3 dB. Low RMS gain and phase errors over a wide bandwidth are attributed to the high precision DAC employed in the control of VGA and PS. Both chips are flip‐chip packaged and undergo upconversion/downconversion via external mixers on a printed circuit board (PCB). System‐level tests with 64‐quadrature amplitude modulation (QAM) show an error vector magnitude (EVM) of 2.72% at 27 GHz for RX and 5.02% at 24 GHz for TX, with a 50‐MBaud modulated signal applied at a data rate of 300 MBps.

Millimeter-Wave Band CMOS RF Phased-Array Transceiver IC Designs for 5G Applications

4.1 A 39GHz-Band CMOS 16-Channel Phased-Array Transceiver IC with a Companion Dual-Stream IF Transceiver IC for 5G NR Base-Station Applications

A 39 GHz Dual-Channel Transceiver Chipset with an Advanced LTCC Package for 5G Multi-Beam MIMO Systems

A 28-GHz CMOS Phased-Array Transceiver Based on LO Phase-Shifting Architecture With Gain Invariant Phase Tuning for 5G New Radio

A Four-Element 7.5–9-Ghz Phased-Array Receiver with 1–8 Simultaneously Reconfigurable Beams in 65-Nm CMOS

A 4-Element 7.5-9 GHz Phased Array Receiver with 8 Simultaneously Reconfigurable Beams in 65 Nm CMOS Technology

A 28ghz Cmos Phased-Array Transceiver Featuring Gain Invariance Based On Lo Phase Shifting Architecture With 0.1-Degree Beam-Steering Resolution For 5g New Radio

38-GHz Phased Array Transmitter and Receiver Based on Scalable Phased Array Modules With Endfire Antenna Arrays for 5G MMW Data Links

A 39ghz 64-Element Phased-Array CMOS Transceiver with Built-in Calibration for Large-Array 5G NR

A 39-GHz 64-Element Phased-Array Transceiver With Built-In Phase and Amplitude Calibrations for Large-Array 5G NR in 65-nm CMOS

Research on CMOS Mm-Wave Circuits and Systems for Wireless Communications

A 24–30-GHz 256-Element Dual-Polarized 5G Phased Array Using Fast On-Chip Beam Calculators and Magnetoelectric Dipole Antennas

A 24‐ to 28‐GHz 4×1 MIMO Transmitter/Receiver for 5G Phased‐Array Applications With High Amplitude and Phase Control

A 28-GHz CMOS Phased-Array Beamformer Utilizing Neutralized Bi-Directional Technique Supporting Dual-Polarized MIMO for 5G NR

An Ultra-compact Bidirectional T/R Folded 25.8-39.2GHz Phased-Array Transceiver Front-End with Embedded TX Power Detection/Self-calibration Path Supporting 64-/256-/512-QAM at 28-/39-GHz band for 5G in 65nm CMOS Technology

A 24–29.5-GHz Highly Linear Phased-Array Transceiver Front-End in 65-nm CMOS Supporting 800-MHz 64-QAM and 400-MHz 256-QAM for 5G New Radio

A 28 GHz transceiver chip for 5G beamforming data links in SiGe BiCMOS

Design of a Broadband Millimeter-Wave Array Antenna for 5G Applications