Abstract:It is an important issue that the axial forces exerting on rotors greatly affect the operation stability of centrifugal pumps. The axial clearance between the impeller shroud and the volute casing cover is a key factor that influences the magnitude and direction of the axial force. The axial force is mainly derived by pressure difference on the outer surface of front and back shrouds and hydraulic pressure on the inner surface of the impeller. The dredging pump studied in this paper was a shrouded centrifugal pump with 9 backward curved back blades on the front shroud. Adjusting the axial position of the impeller could simultaneously change the front clearance and back clearance. Numerical simulations were carried out for 3 axial clearances. Based on RANS numerical method, SST k-ω turbulence model was adopted to calculate the 3D turbulence flow in the whole flow passage of the pump. The impeller and the back-blade domain were set as rotating domains with the same rotational speed in the model test. The front and back shroud were set as rotating walls with the same rotational speed. For each operating condition, average values of the three were taken as the final results. The predicted efficiency, head and shaft power agreed well with the experimental results, which indicated the reliability of the numerical method. The relationship between axial clearance and characteristics of pump performance and axial force was analyzed within a wide range of flow rates. The numerical results showed that as the front clearance increased, the efficiency of the pump dramatically declined and the head decreased by different amplitudes, while the shaft power changed little. The component axial force on the back shroud was much larger than others, and thus it determined the direction of the gross axial force. By contrast, the component axial force on impeller inner surface was the smallest. The 3 components of axial force changed with flow rate and axial clearance on different levels. The total axial force gradually decreased as the flow rate increased, and it was the larger when the front clearance was wider. Affected by the rotating back blades, the pressure distribution on the front shroud was in disorder and the pressure gradient was large, while on back shroud, the pressure distribution presented smooth circles and the pressure changed uniformly in radial. As the front clearance increased, the pressure distribution became more homogeneous on both the front shroud and the back shroud. The pressure was larger on the back shroud than that on the front shroud, the area of the back shroud was larger, and hence the characteristics of the total axial force was determined by the component on the back shroud. Therefore, in the preliminary hydraulic design of dredging pumps, pump performance and axial force characteristics should be comprehensively considered and set suitable axial clearance sizes.

Numerical simulation on the influence of root clearance on the hydraulic performance of axial flow pump device

Analysis of flow characteristics in the volute casing of centrifugal pump based on numerical simulation

Numerical Simulation of Flow in Centrifugal Pump with Complex Impeller

Numerical Simulation of Inner Flow Field in Centrifugal Impeller with Long, Middle and Short Blades

Cavitation Performance Improvement of High Specific Speed Mixed-Flow Pump

Numerical Investigation of Influence of Rotor-Rotor Gap on Performances of Contra-Rotating Axial Flow Pump

Numerical analysis of axial force on dredging pump considering influence of axial clearance

The influence of ring clearance on the performance of a double-suction centrifugal pump

Numerical Investigation of Tip Clearance Effects on the Performance and Flow Pattern Within a Sewage Pump

Numerical Investigation and Experiment on Natural Circulation Resistance and Energy Characteristics in a Circulating Axial Pump

Numerical Simulation of the Cavitation Characteristics of A Mixed-Flow Pump

Numerical investigation of non-uniform inflow effects on internal and external characteristics of an axial-flow pump

Investigation of CFD Calculation Method of a Centrifugal Pump with Unshrouded Impeller

Influence factors of clearance leakage flowrate and clearance hydraulic axial force of pump-turbine

Effect of Axial Clearance on the Efficiency of a Shrouded Centrifugal Pump

Energy Performance and Radial Force of a Mixed-Flow Pump with Symmetrical and Unsymmetrical Tip Clearances

Numerical simulation and model test of the influence of guide vane angle on the performance of axial flow pump

Numerical Investigation on Cavitation Performance for Centrifugal Pumps with Different Impeller Inlet Geometry

Numerical Investigation of Pressure Fluctuation Characteristics in a Centrifugal Pump with Variable Axial Clearance

Investigation of cavitation and flow characteristics of tip clearance of bidirectional axial flow pump with different clearances

Numerical investigation of internal flow characteristics in a mixed-flow pump with eccentric impeller