Abstract:Recent developments in manufacturing require holes on composite materials, especially on the carbon fiber reinforced polymer (CFRP) with smooth hole periphery, low delamination, burr formation, taper, better circularity, and a high processing speed. Its non-conductive surface (epoxy layering) limits its machining through electrical discharge machining (EDM). To overcome this limitation, an aluminum fixture has been designed to guide the copper electrode of EDM for producing holes on a CFRP sheet of 1 mm thickness at low machining complexity, cost, time, delamination, burr in hole periphery and without affecting the material’s surface quality and performance. Even components with high geometrical complexity can also be drilled through this approach. Here, a multi-quality analysis called grey relational analysis is developed for examining the hole quality attributes, considering peak current, pulse on and off time, and flushing pressure as input parameters. This approach points out the optimum factor level setting and critical parameters (pulse-on time and peak current) that regulate the hole attributes (entrance and exit diameter, circularity, taper, material removal, and tool wear rate). An artificial neural network model has been designed and trained through experimental data sets. This model can also be adopted during the determination of hole quality attributes when the parameter settings are beyond a defined boundary, as the regression analysis value is very close to 1, and model performance is 4.99e-10. Peak current = 4 A, pulse-on time = 25 μs, pulse-off time=25 μs, and flushing pressure = 0.6 MPa were the optimum drilling parameters. In the initial hole, average burr length is 391.75 μm, and delamination of 539.3 μm is noticed. But burr formation is very negligible with delamination of 350.7 μm being observed with uniform circularity (0.979), low taper angle (−0.81354°), and TWR (0.000069 g/min) under optimum drilling conditions through this drilling approach.

A novel approach for removal of delaminated fibers of a reinforced composites using electrochemical discharge machining

Design and Analysis of CFRP Drilling by Electrical Discharge Machining

CFRP composite drilling through electrical discharge machining using aluminum as fixture plate

Dry electrical discharge machining for deburring drilled holes in CFRP composite

The Feasibility Analysis of Electrical-Discharge Machining of Carbon-Carbon Composites

A novel reverse helical milling process for reducing push-out delamination of CFRP

Improving resistance to embedded delaminations by adding CNTs to epoxy in carbon/(epoxy + CNT) composites

Experimental Investigation of drill tool types on delamination error in drilling of CFRP

An approach towards damage free machining of CFRP and GFRP composite material: a review

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite

Development of Laser Drilling Strategy for Thick Carbon Fibre Reinforced Polymer Composites (CFRP)

An experimental and empirical assessment of machining damage of hybrid glass-carbon FRP composite during abrasive water jet machining

IMPROVEMENT OF SURFACE PROPERTIES OF CARBON FIBER REINFORCED EPOXY COMPOSITES USING SOLID LUBRICANTS DURING MACHINING PROCESSES

Electrical Discharge Machining of SiC and Gr Reinforced 6061-T6 Aluminum Alloy Hybrid Composite Fabricated by Friction Stir Processing

Machinability investigation of natural fibers reinforced polymer matrix composite under drilling: Leveraging machine learning in bioengineering applications

Hole Quality and Damage in Drilling Carbon/Epoxy Composites by Electrical Discharge Machining

Investigation on Deposition of the Machined By-Products and Its Reduction during Electrochemical Discharge Machining (ECDM)

Electrical discharge machining assessment of AA7075/Rice Husk Ash composite using response surface methodology

Efficient recovery of carbon fibers from carbon fiber-reinforced polymers using direct discharge electrical pulses

Machining of Fibre Reinforced Plastic Composite Materials